diff options
Diffstat (limited to 'stmhal/boards/LIMIFROG')
| -rw-r--r-- | stmhal/boards/LIMIFROG/board_init.c | 154 | ||||
| -rw-r--r-- | stmhal/boards/LIMIFROG/mpconfigboard.h | 61 | ||||
| -rw-r--r-- | stmhal/boards/LIMIFROG/mpconfigboard.mk | 5 | ||||
| -rw-r--r-- | stmhal/boards/LIMIFROG/pins.csv | 114 | ||||
| -rw-r--r-- | stmhal/boards/LIMIFROG/stm32l4xx_hal_conf.h | 373 |
5 files changed, 0 insertions, 707 deletions
diff --git a/stmhal/boards/LIMIFROG/board_init.c b/stmhal/boards/LIMIFROG/board_init.c deleted file mode 100644 index 72f920842..000000000 --- a/stmhal/boards/LIMIFROG/board_init.c +++ /dev/null @@ -1,154 +0,0 @@ -// The code is this file allows the user to enter DFU mode when the board -// starts up, by connecting POS10 on the external connector to GND. -// The code itself is taken from the LimiFrog software repository found at -// https://github.com/LimiFrog/LimiFrog-SW, and the original license header -// is copied below. - -#include STM32_HAL_H - -static void LBF_DFU_If_Needed(void); - -void LIMIFROG_board_early_init(void) { - LBF_DFU_If_Needed(); -} - -/******************************************************************************* - * LBF_DFU_If_Needed.c - * - * (c)2015 LimiFrog / CYMEYA - * This program is licensed under the terms of the MIT License. - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND. - * Please refer to the License File LICENSE.txt located at the root of this - * project for full licensing conditions, - * or visit https://opensource.org/licenses/MIT. - ******************************************************************************/ - -#define __LIMIFROG_02 - -/* ==== BTLE (excl UART) ======================================== */ -// PC9 = BT_RST (active high) - -#define BT_RST_PIN GPIO_PIN_9 -#define BT_RST_PORT GPIOC - -// Position 10 -#ifdef __LIMIFROG_01 - #define CONN_POS10_PIN GPIO_PIN_9 - #define CONN_POS10_PORT GPIOB -#else - #define CONN_POS10_PIN GPIO_PIN_8 - #define CONN_POS10_PORT GPIOB -#endif - -static inline void GPIO_HIGH(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) -{ - GPIOx->BSRR = (uint32_t)GPIO_Pin; -} - -static inline int IS_GPIO_RESET(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) -{ - GPIO_PinState bitstatus; - if((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET) - { - bitstatus = GPIO_PIN_SET; - } - else - { - bitstatus = GPIO_PIN_RESET; - } - return (bitstatus==GPIO_PIN_RESET); -} - -/************************************************************** - RATIONALE FOR THIS FUNCTION : - - - The STM32 embeds in ROM a bootloader that allows to - obtain code and boot from a number of different interfaces, - including USB in a mode called "DFU" (Device Frimware Update) - [see AN3606 from ST for full details] - This bootloader code is executed instead of the regular - application code when pin BOOT0 is pulled-up (which on - LimiFrog0.2 is achieved by pressing the general-purpose - pushbutton switch on the side. - - The bootloader monitors a number of IOs of the STM32 to decide - from which interface it should boot. - - Problem in LimiFrog (up to versions 0.2a at least): upon - power-up the BLE modules generates some activity on UART3, - which is part of the pins monitored by the STM32. - This misleads the bootloader in trying to boot from UART3 - and, as a result, not continuing with booting from USB. - - - This code implements an alternative solution to launch the - bootloader while making sure UART3 remains stable. - - The idea it to start application code with a check, prior to any - other applicative code, of whether USB bootload is required (as - flagged by a GPIO pulled low at reset, in the same way as BOOT0). - The hadware reset pin of BLE is asserted (so that now it won't - generate any acitivity on UART3), and if USB bootload is required : - bootload ROM is remapped at address 0x0, stack pointer is - updated and the code is branched to the start of the bootloader. - - This code is run prior to any applicative configuration of clocks, - IRQs etc. -- the STM32 is therefore still running from MSI - - THIS FUNCTION MAY BE SUPPRESSED IF YOU NEVER NEED TO BOOT DFU MODE - - ********************************************************************/ - -static void LBF_DFU_If_Needed(void) -{ - - - GPIO_InitTypeDef GPIO_InitStruct; - - - // Initialize and assert pin BTLE_RST - // (hw reset to BLE module, so it won't drive UART3) - - __GPIOC_CLK_ENABLE(); - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_LOW; - GPIO_InitStruct.Pin = BT_RST_PIN; - HAL_GPIO_Init(BT_RST_PORT, &GPIO_InitStruct); - - GPIO_HIGH(BT_RST_PORT, BT_RST_PIN); // assert BTLE reset - - - /* -- Bootloader will be called if position 10 on the extension port - is actively pulled low -- */ - // Note - this is an arbitrary choice, code could be modified to - // monitor another GPIO of the STM32 and/or decide that active level - // is high rather than low - - - // Initialize Extension Port Position 10 = PB8 (bears I2C1_SCL) - // Use weak pull-up to detect if pin is externally pulled low - - __GPIOB_CLK_ENABLE(); - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Pin = CONN_POS10_PIN; - HAL_GPIO_Init(CONN_POS10_PORT, &GPIO_InitStruct); - - // If selection pin pulled low... - if ( IS_GPIO_RESET(CONN_POS10_PORT, CONN_POS10_PIN )) - - { - // Remap bootloader ROM (ie System Flash) to address 0x0 - SYSCFG->MEMRMP = 0x00000001; - - // Init stack pointer with value residing at ROM base - asm ( - "LDR R0, =0x00000000\n\t" // load ROM base address" - "LDR SP,[R0, #0]\n\t" // assign main stack pointer" - ); - - // Jump to address pointed by 0x00000004 -- */ - - asm ( - "LDR R0,[R0, #4]\n\t" // load bootloader address - "BX R0\n\t" - ); - - } -} diff --git a/stmhal/boards/LIMIFROG/mpconfigboard.h b/stmhal/boards/LIMIFROG/mpconfigboard.h deleted file mode 100644 index 42b862fcf..000000000 --- a/stmhal/boards/LIMIFROG/mpconfigboard.h +++ /dev/null @@ -1,61 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "LIMIFROG" -#define MICROPY_HW_MCU_NAME "STM32L476" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (0) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (0) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (0) - -#define MICROPY_BOARD_EARLY_INIT LIMIFROG_board_early_init -void LIMIFROG_board_early_init(void); - -// MSI is used and is 4MHz -#define MICROPY_HW_CLK_PLLM (1) -#define MICROPY_HW_CLK_PLLN (40) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7) -#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2) -#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2) - -#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 - -// USART config -#define MICROPY_HW_UART3_TX (pin_C10) -#define MICROPY_HW_UART3_RX (pin_C11) - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B8) -#define MICROPY_HW_I2C1_SDA (pin_B9) -#define MICROPY_HW_I2C2_SCL (pin_B10) -#define MICROPY_HW_I2C2_SDA (pin_B11) - -// SPI busses -#define MICROPY_HW_SPI1_NSS (pin_A4) -#define MICROPY_HW_SPI1_SCK (pin_A5) -#define MICROPY_HW_SPI1_MISO (pin_A6) -#define MICROPY_HW_SPI1_MOSI (pin_A7) - -#define MICROPY_HW_SPI3_NSS (pin_A15) -#define MICROPY_HW_SPI3_SCK (pin_B3) -#define MICROPY_HW_SPI3_MISO (pin_B4) -#define MICROPY_HW_SPI3_MOSI (pin_B5) - -#define MICROPY_HW_USRSW_PIN (pin_A15) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_C3) // red -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// USB config -// #define MICROPY_HW_USB_OTG_ID_PIN (pin_C12) // This is not the official ID Pin which should be PA10 diff --git a/stmhal/boards/LIMIFROG/mpconfigboard.mk b/stmhal/boards/LIMIFROG/mpconfigboard.mk deleted file mode 100644 index a1304b655..000000000 --- a/stmhal/boards/LIMIFROG/mpconfigboard.mk +++ /dev/null @@ -1,5 +0,0 @@ -MCU_SERIES = l4 -CMSIS_MCU = STM32L476xx -AF_FILE = boards/stm32l476_af.csv -LD_FILE = boards/stm32l476xe.ld -TEXT_ADDR = 0x08004000 diff --git a/stmhal/boards/LIMIFROG/pins.csv b/stmhal/boards/LIMIFROG/pins.csv deleted file mode 100644 index 52f96b669..000000000 --- a/stmhal/boards/LIMIFROG/pins.csv +++ /dev/null @@ -1,114 +0,0 @@ -PA0,PA0 -PA1,PA1 -PA2,PA2 -PA3,PA3 -PA4,PA4 -PA5,PA5 -PA6,PA6 -PA7,PA7 -PA8,PA8 -PA9,PA9 -PA10,PA10 -PA11,PA11 -PA12,PA12 -PA13,PA13 -PA14,PA14 -PA15,PA15 -PB0,PB0 -PB1,PB1 -PB2,PB2 -PB3,PB3 -PB4,PB4 -PB5,PB5 -PB6,PB6 -PB7,PB7 -PB8,PB8 -PB9,PB9 -PB10,PB10 -PB11,PB11 -PB12,PB12 -PB13,PB13 -PB14,PB14 -PB15,PB15 -PC0,PC0 -PC1,PC1 -PC2,PC2 -PC3,PC3 -PC4,PC4 -PC5,PC5 -PC6,PC6 -PC7,PC7 -PC8,PC8 -PC9,PC9 -PC10,PC10 -PC11,PC11 -PC12,PC12 -PC13,PC13 -PC14,PC14 -PC15,PC15 -PD0,PD0 -PD1,PD1 -PD2,PD2 -PD3,PD3 -PD4,PD4 -PD5,PD5 -PD6,PD6 -PD7,PD7 -PD8,PD8 -PD9,PD9 -PD10,PD10 -PD11,PD11 -PD12,PD12 -PD13,PD13 -PD14,PD14 -PD15,PD15 -PE0,PE0 -PE1,PE1 -PE2,PE2 -PE3,PE3 -PE4,PE4 -PE5,PE5 -PE6,PE6 -PE7,PE7 -PE8,PE8 -PE9,PE9 -PE10,PE10 -PE11,PE11 -PE12,PE12 -PE13,PE13 -PE14,PE14 -PE15,PE15 -PF0,PF0 -PF1,PF1 -PF2,PF2 -PF3,PF3 -PF4,PF4 -PF5,PF5 -PF6,PF6 -PF7,PF7 -PF8,PF8 -PF9,PF9 -PF10,PF10 -PF11,PF11 -PF12,PF12 -PF13,PF13 -PF14,PF14 -PF15,PF15 -PG0,PG0 -PG1,PG1 -PG2,PG2 -PG3,PG3 -PG4,PG4 -PG5,PG5 -PG6,PG6 -PG7,PG7 -PG8,PG8 -PG9,PG9 -PG10,PG10 -PG11,PG11 -PG12,PG12 -PG13,PG13 -PG14,PG14 -PG15,PG15 -PH0,PH0 -PH1,PH1 diff --git a/stmhal/boards/LIMIFROG/stm32l4xx_hal_conf.h b/stmhal/boards/LIMIFROG/stm32l4xx_hal_conf.h deleted file mode 100644 index 9348e0679..000000000 --- a/stmhal/boards/LIMIFROG/stm32l4xx_hal_conf.h +++ /dev/null @@ -1,373 +0,0 @@ -/** - ****************************************************************************** - * @file stm32l4xx_hal_conf.h - * @author MCD Application Team - * @version V1.2.0 - * @date 25-November-2015 - * @brief HAL configuration template file. - * This file should be copied to the application folder and renamed - * to stm32l4xx_hal_conf.h. - ****************************************************************************** - * @attention - * - * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32L4xx_HAL_CONF_H -#define __STM32L4xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -#define USE_USB_FS -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -#define HAL_ADC_MODULE_ENABLED -#define HAL_CAN_MODULE_ENABLED -/* #define HAL_COMP_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -/* #define HAL_CRC_MODULE_ENABLED */ -/* #define HAL_CRYP_MODULE_ENABLED */ -#define HAL_DAC_MODULE_ENABLED -/* #define HAL_DFSDM_MODULE_ENABLED */ -#define HAL_DMA_MODULE_ENABLED -/* #define HAL_FIREWALL_MODULE_ENABLED */ -#define HAL_FLASH_MODULE_ENABLED -/* #define HAL_HCD_MODULE_ENABLED */ -/* #define HAL_NAND_MODULE_ENABLED */ -/* #define HAL_NOR_MODULE_ENABLED */ -/* #define HAL_SRAM_MODULE_ENABLED */ -#define HAL_GPIO_MODULE_ENABLED -#define HAL_I2C_MODULE_ENABLED -/* #define HAL_IRDA_MODULE_ENABLED */ -/* #define HAL_IWDG_MODULE_ENABLED */ -/* #define HAL_LCD_MODULE_ENABLED */ -/* #define HAL_LPTIM_MODULE_ENABLED */ -/* #define HAL_OPAMP_MODULE_ENABLED */ -#define HAL_PCD_MODULE_ENABLED -#define HAL_PWR_MODULE_ENABLED -/* #define HAL_QSPI_MODULE_ENABLED */ -#define HAL_RCC_MODULE_ENABLED -#define HAL_RNG_MODULE_ENABLED -#define HAL_RTC_MODULE_ENABLED -/* #define HAL_SAI_MODULE_ENABLED */ -#define HAL_SD_MODULE_ENABLED -/* #define HAL_SMARTCARD_MODULE_ENABLED */ -/* #define HAL_SMBUS_MODULE_ENABLED */ -#define HAL_SPI_MODULE_ENABLED -/* #define HAL_SWPMI_MODULE_ENABLED */ -#define HAL_TIM_MODULE_ENABLED -/* #define HAL_TSC_MODULE_ENABLED */ -#define HAL_UART_MODULE_ENABLED -/* #define HAL_USART_MODULE_ENABLED */ -/* #define HAL_WWDG_MODULE_ENABLED */ - - -/* ########################## Oscillator Values adaptation ####################*/ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal Multiple Speed oscillator (MSI) default value. - * This value is the default MSI range value after Reset. - */ -#if !defined (MSI_VALUE) - #define MSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* MSI_VALUE */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature. */ -/** - * @brief External Low Speed oscillator (LSE) value. - * This value is used by the UART, RTC HAL module to compute the system frequency - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ -#endif /* LSE_VALUE */ - -#if !defined (LSE_STARTUP_TIMEOUT) - #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief External clock source for SAI1 peripheral - * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source - * frequency. - */ -#if !defined (EXTERNAL_SAI1_CLOCK_VALUE) - #define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/ -#endif /* EXTERNAL_SAI1_CLOCK_VALUE */ - -/** - * @brief External clock source for SAI2 peripheral - * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source - * frequency. - */ -#if !defined (EXTERNAL_SAI2_CLOCK_VALUE) - #define EXTERNAL_SAI2_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/ -#endif /* EXTERNAL_SAI2_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */ -#define USE_RTOS 0 -#define PREFETCH_ENABLE 1 -#define INSTRUCTION_CACHE_ENABLE 1 -#define DATA_CACHE_ENABLE 1 - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1 */ - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32l4xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32l4xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32l4xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_DFSDM_MODULE_ENABLED - #include "stm32l4xx_hal_dfsdm.h" -#endif /* HAL_DFSDM_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32l4xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32l4xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32l4xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_COMP_MODULE_ENABLED - #include "stm32l4xx_hal_comp.h" -#endif /* HAL_COMP_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32l4xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED - #include "stm32l4xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32l4xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_FIREWALL_MODULE_ENABLED - #include "stm32l4xx_hal_firewall.h" -#endif /* HAL_FIREWALL_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32l4xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED - #include "stm32l4xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED - #include "stm32l4xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED - #include "stm32l4xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32l4xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32l4xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_LCD_MODULE_ENABLED - #include "stm32l4xx_hal_lcd.h" -#endif /* HAL_LCD_MODULE_ENABLED */ - -#ifdef HAL_LPTIM_MODULE_ENABLED -#include "stm32l4xx_hal_lptim.h" -#endif /* HAL_LPTIM_MODULE_ENABLED */ - -#ifdef HAL_OPAMP_MODULE_ENABLED -#include "stm32l4xx_hal_opamp.h" -#endif /* HAL_OPAMP_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32l4xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_QSPI_MODULE_ENABLED - #include "stm32l4xx_hal_qspi.h" -#endif /* HAL_QSPI_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED - #include "stm32l4xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32l4xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SAI_MODULE_ENABLED - #include "stm32l4xx_hal_sai.h" -#endif /* HAL_SAI_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED - #include "stm32l4xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SMBUS_MODULE_ENABLED - #include "stm32l4xx_hal_smbus.h" -#endif /* HAL_SMBUS_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32l4xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_SWPMI_MODULE_ENABLED - #include "stm32l4xx_hal_swpmi.h" -#endif /* HAL_SWPMI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32l4xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_TSC_MODULE_ENABLED - #include "stm32l4xx_hal_tsc.h" -#endif /* HAL_TSC_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32l4xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32l4xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32l4xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32l4xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32l4xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32l4xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED - #include "stm32l4xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t* file, uint32_t line); -#else - #define assert_param(expr) ((void)0) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32L4xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |