1 files changed, 0 insertions, 61 deletions
diff --git a/stmhal/boards/LIMIFROG/mpconfigboard.h b/stmhal/boards/LIMIFROG/mpconfigboard.h
deleted file mode 100644
index 42b862fcf..000000000
--- a/stmhal/boards/LIMIFROG/mpconfigboard.h
+++ /dev/null
@@ -1,61 +0,0 @@
-#define MICROPY_HW_BOARD_NAME       "LIMIFROG"
-#define MICROPY_HW_MCU_NAME         "STM32L476"
-
-#define MICROPY_HW_HAS_SWITCH       (1)
-#define MICROPY_HW_HAS_FLASH        (1)
-#define MICROPY_HW_HAS_SDCARD       (0)
-#define MICROPY_HW_HAS_MMA7660      (0)
-#define MICROPY_HW_HAS_LIS3DSH      (0)
-#define MICROPY_HW_HAS_LCD          (0)
-#define MICROPY_HW_ENABLE_RNG       (1)
-#define MICROPY_HW_ENABLE_RTC       (1)
-#define MICROPY_HW_ENABLE_TIMER     (1)
-#define MICROPY_HW_ENABLE_SERVO     (0)
-#define MICROPY_HW_ENABLE_DAC       (0)
-#define MICROPY_HW_ENABLE_CAN       (0)
-
-#define MICROPY_BOARD_EARLY_INIT    LIMIFROG_board_early_init
-void LIMIFROG_board_early_init(void);
-
-// MSI is used and is 4MHz
-#define MICROPY_HW_CLK_PLLM (1)
-#define MICROPY_HW_CLK_PLLN (40)
-#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
-#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
-#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
-
-#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_4
-
-// USART config
-#define MICROPY_HW_UART3_TX (pin_C10)
-#define MICROPY_HW_UART3_RX (pin_C11)
-
-// I2C busses
-#define MICROPY_HW_I2C1_SCL (pin_B8)
-#define MICROPY_HW_I2C1_SDA (pin_B9)
-#define MICROPY_HW_I2C2_SCL (pin_B10)
-#define MICROPY_HW_I2C2_SDA (pin_B11)
-
-// SPI busses
-#define MICROPY_HW_SPI1_NSS     (pin_A4)
-#define MICROPY_HW_SPI1_SCK     (pin_A5)
-#define MICROPY_HW_SPI1_MISO    (pin_A6)
-#define MICROPY_HW_SPI1_MOSI    (pin_A7)
-
-#define MICROPY_HW_SPI3_NSS     (pin_A15)
-#define MICROPY_HW_SPI3_SCK     (pin_B3)
-#define MICROPY_HW_SPI3_MISO    (pin_B4)
-#define MICROPY_HW_SPI3_MOSI    (pin_B5)
-
-#define MICROPY_HW_USRSW_PIN        (pin_A15)
-#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
-#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
-#define MICROPY_HW_USRSW_PRESSED    (1)
-
-// LEDs
-#define MICROPY_HW_LED1             (pin_C3) // red
-#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
-#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
-
-// USB config
-// #define MICROPY_HW_USB_OTG_ID_PIN      (pin_C12) // This is not the official ID Pin which should be PA10