blob: 00b033006ba9abd6841709fa2e6d3b8ed4caa2d4 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
|
#define MICROPY_HW_BOARD_NAME "NUCLEO-L476RG"
#define MICROPY_HW_MCU_NAME "STM32L476RG"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_ENABLE_DAC (1)
// MSI is used and is 4MHz
#define MICROPY_HW_CLK_PLLM (1)
#define MICROPY_HW_CLK_PLLN (40)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
// The board has an external 32kHz crystal
#define MICROPY_HW_RTC_USE_LSE (1)
// UART config
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
#define MICROPY_HW_I2C3_SCL (pin_C0)
#define MICROPY_HW_I2C3_SDA (pin_C1)
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_B3)
#define MICROPY_HW_SPI1_MISO (pin_B4)
#define MICROPY_HW_SPI1_MOSI (pin_B5)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// CAN bus
#define MICROPY_HW_CAN1_TX (pin_A12)
#define MICROPY_HW_CAN1_RX (pin_A11)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED1 (pin_A5) // Green LED on Nucleo
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config
#define MICROPY_HW_USB_FS (1)
|
