| Age | Commit message (Collapse) | Author |
|---|
|
The SCSI driver calls GetCapacity to get the block size and number of
blocks of the underlying block-device/LUN. It caches these values and uses
them later on to verify that reads/writes are within the bounds of the LUN.
But, prior to this commit, there was only one set of cached values for all
LUNs, so the bounds checking for a LUN could use incorrect values, values
from one of the other LUNs that most recently updated the cached values.
This would lead to failed SCSI requests.
This commit fixes this issue by having separate cached values for each LUN.
Signed-off-by: Damien George <damien@micropython.org>
|
|
|
|
|
|
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID. They are both
enabled by default.
|
|
Eventually these responses could be filled in by a function to make their
contents dynamic, depending on the attached logical units. But for now
they are fixed, and this patch fixes the MODE SENSE(6) responses so it is
the correct length with the correct header.
|
|
So the MSC interface can customise the inquiry response based on the
attached logical units.
|
|
Because py/mpconfig.h has header include guards.
|
|
To enable define MICROPY_HW_USB_CDC_NUM to 3.
|
|
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
|
|
Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to
regularly check if buffered data needed to be sent out to the USB host.
This wasted resources (CPU, power) if no data needed to be sent.
This commit changes how the USB CDC transmits buffered data:
- When new data is first available to send the data is queued immediately
on the USB IN endpoint, ready to be sent as soon as possible.
- Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait.
- When the low-level USB driver has finished sending out the data queued
in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately
queues any outstanding data, waiting for the next IN frame.
The benefits on this new approach are:
- SOF IRQ does not need to run continuously so device has a better chance
to sleep for longer, and be more responsive to other IRQs.
- Because SOF IRQ is off, current consumption is reduced by a small amount,
roughly 200uA when USB is connected (measured on PYBv1.0).
- CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is
unchanged).
- When USB is connected, Python code that is executing is slightly faster
because SOF IRQ no longer interrupts continuously.
- On F733 with USB HS, CDC tx throughput is about the same as prior to this
commit.
- On F733 with USB HS, Python code is about 5% faster because of no SOF.
As part of this refactor, the serial port should no longer echo initial
characters when the serial port is first opened (this only used to happen
rarely on USB FS, but on USB HS is was more evident).
|
|
pyb.USB_VCP().isconnected() will now return False if the USB is
disconnected after having previously been connected.
See issue #4210.
|
|
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC. It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it. The second one is
available for general use.
This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM. Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints. The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Also remove trailing whitespace and convert tabs to spaces.
|
|
|
|
This patch allows to completely compile-out support for USB, and no-USB is
now the default. If a board wants to enable USB it should define:
#define MICROPY_HW_ENABLE_USB (1)
And then one or more of the following to select the USB PHY:
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_HS (1)
#define MICROPY_HW_USB_HS_IN_FS (1)
|
|
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode. To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY. High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.
This patch has been tested on an STM32F733.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
|
