diff options
Diffstat (limited to 'stmhal/boards/STM32L476DISC/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/STM32L476DISC/mpconfigboard.h | 68 |
1 files changed, 0 insertions, 68 deletions
diff --git a/stmhal/boards/STM32L476DISC/mpconfigboard.h b/stmhal/boards/STM32L476DISC/mpconfigboard.h deleted file mode 100644 index 9dbadd530..000000000 --- a/stmhal/boards/STM32L476DISC/mpconfigboard.h +++ /dev/null @@ -1,68 +0,0 @@ -#define MICROPY_BOARD_EARLY_INIT STM32L476DISC_board_early_init -void STM32L476DISC_board_early_init(void); - -#define MICROPY_HW_BOARD_NAME "L476-DISCO" -#define MICROPY_HW_MCU_NAME "STM32L476" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (0) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (0) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (0) - -// use external SPI flash for storage -#define MICROPY_HW_SPIFLASH_SIZE_BITS (128 * 1024 * 1024) -#define MICROPY_HW_SPIFLASH_CS (pin_E11) -#define MICROPY_HW_SPIFLASH_SCK (pin_E10) -#define MICROPY_HW_SPIFLASH_MOSI (pin_E12) -#define MICROPY_HW_SPIFLASH_MISO (pin_E13) - -// MSI is used and is 4MHz -#define MICROPY_HW_CLK_PLLM (1) -#define MICROPY_HW_CLK_PLLN (40) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7) -#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2) -#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2) - -#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 - -// USART config -#define MICROPY_HW_UART2_TX (pin_D5) -#define MICROPY_HW_UART2_RX (pin_D6) -// USART 2 is connected to the virtual com port on the ST-LINK -#define MICROPY_HW_UART_REPL PYB_UART_2 -#define MICROPY_HW_UART_REPL_BAUD 115200 - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B6) -#define MICROPY_HW_I2C1_SDA (pin_B7) -#define MICROPY_HW_I2C2_SCL (pin_B10) -#define MICROPY_HW_I2C2_SDA (pin_B11) - -// SPI busses -#define MICROPY_HW_SPI2_NSS (pin_D0) -#define MICROPY_HW_SPI2_SCK (pin_D1) -#define MICROPY_HW_SPI2_MISO (pin_D3) -#define MICROPY_HW_SPI2_MOSI (pin_D4) - -// Joystick is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_A0) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_B2) // red -#define MICROPY_HW_LED2 (pin_E8) // green -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// USB config -// #define MICROPY_HW_USB_OTG_ID_PIN (pin_C12) // This is not the official ID Pin which should be PA10 |