diff options
Diffstat (limited to 'stmhal/boards/STM32F7DISC')
| -rw-r--r-- | stmhal/boards/STM32F7DISC/board_init.c | 15 | ||||
| -rw-r--r-- | stmhal/boards/STM32F7DISC/mpconfigboard.h | 82 | ||||
| -rw-r--r-- | stmhal/boards/STM32F7DISC/mpconfigboard.mk | 4 | ||||
| -rw-r--r-- | stmhal/boards/STM32F7DISC/pins.csv | 53 | ||||
| -rw-r--r-- | stmhal/boards/STM32F7DISC/stm32f7xx_hal_conf.h | 429 |
5 files changed, 0 insertions, 583 deletions
diff --git a/stmhal/boards/STM32F7DISC/board_init.c b/stmhal/boards/STM32F7DISC/board_init.c deleted file mode 100644 index 4530a4706..000000000 --- a/stmhal/boards/STM32F7DISC/board_init.c +++ /dev/null @@ -1,15 +0,0 @@ -#include STM32_HAL_H - -void STM32F7DISC_board_early_init(void) { - GPIO_InitTypeDef GPIO_InitStructure; - - __GPIOK_CLK_ENABLE(); - - // Turn off the backlight. LCD_BL_CTRL = PK3 - GPIO_InitStructure.Pin = GPIO_PIN_3; - GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStructure.Pull = GPIO_PULLUP; - GPIO_InitStructure.Speed = GPIO_SPEED_HIGH; - HAL_GPIO_Init(GPIOK, &GPIO_InitStructure); - HAL_GPIO_WritePin(GPIOK, GPIO_PIN_3, GPIO_PIN_RESET); -} diff --git a/stmhal/boards/STM32F7DISC/mpconfigboard.h b/stmhal/boards/STM32F7DISC/mpconfigboard.h deleted file mode 100644 index 44a39c0a1..000000000 --- a/stmhal/boards/STM32F7DISC/mpconfigboard.h +++ /dev/null @@ -1,82 +0,0 @@ -#define STM32F7DISC - -#define MICROPY_HW_BOARD_NAME "F7DISC" -#define MICROPY_HW_MCU_NAME "STM32F746" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (0) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (1) - -#define MICROPY_BOARD_EARLY_INIT STM32F7DISC_board_early_init -void STM32F7DISC_board_early_init(void); - -// HSE is 25MHz -// VCOClock = HSE * PLLN / PLLM = 25 MHz * 432 / 25 = 432 MHz -// SYSCLK = VCOClock / PLLP = 432 MHz / 2 = 216 MHz -// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 432 MHz / 9 = 48 MHz -#define MICROPY_HW_CLK_PLLM (25) -#define MICROPY_HW_CLK_PLLN (432) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (9) - -// From the reference manual, for 2.7V to 3.6V -// 151-180 MHz => 5 wait states -// 181-210 MHz => 6 wait states -// 211-216 MHz => 7 wait states -#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_7 // 210-216 MHz needs 7 wait states - -// UART config -#define MICROPY_HW_UART1_TX (pin_A9) -#define MICROPY_HW_UART1_RX (pin_B7) -#define MICROPY_HW_UART6_TX (pin_C6) -#define MICROPY_HW_UART6_RX (pin_C7) -#define MICROPY_HW_UART7_TX (pin_F6) -#define MICROPY_HW_UART7_RX (pin_F7) -#define MICROPY_HW_UART_REPL PYB_UART_1 -#define MICROPY_HW_UART_REPL_BAUD 115200 - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B8) -#define MICROPY_HW_I2C1_SDA (pin_B9) - -#define MICROPY_HW_I2C3_SCL (pin_H7) -#define MICROPY_HW_I2C3_SDA (pin_H8) - -// SPI -#define MICROPY_HW_SPI2_NSS (pin_I0) -#define MICROPY_HW_SPI2_SCK (pin_I1) -#define MICROPY_HW_SPI2_MISO (pin_B14) -#define MICROPY_HW_SPI2_MOSI (pin_B15) - -// USRSW is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_I11) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_I1) // green -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// SD card detect switch -#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13) -#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) -#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) - -// USB config (CN13 - USB OTG FS) -// The Hardware VBUS detect only works on pin PA9. The STM32F7 Discovery uses -// PA9 for VCP_TX functionality and connects the VBUS to pin J12 (so software -// only detect). So we don't define the VBUS detect pin since that requires PA9. - -/*#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_J12)*/ -#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) diff --git a/stmhal/boards/STM32F7DISC/mpconfigboard.mk b/stmhal/boards/STM32F7DISC/mpconfigboard.mk deleted file mode 100644 index 7c6bc4584..000000000 --- a/stmhal/boards/STM32F7DISC/mpconfigboard.mk +++ /dev/null @@ -1,4 +0,0 @@ -MCU_SERIES = f7 -CMSIS_MCU = STM32F746xx -AF_FILE = boards/stm32f746_af.csv -LD_FILE = boards/stm32f746.ld diff --git a/stmhal/boards/STM32F7DISC/pins.csv b/stmhal/boards/STM32F7DISC/pins.csv deleted file mode 100644 index 1aa8a9b3a..000000000 --- a/stmhal/boards/STM32F7DISC/pins.csv +++ /dev/null @@ -1,53 +0,0 @@ -A0,PA0 -A1,PF10 -A2,PF9 -A3,PF8 -A4,PF7 -A5,PF6 -D0,PC7 -D1,PC6 -D2,PG6 -D3,PB4 -D4,PG7 -D5,PA8 -D6,PH6 -D7,PI3 -D8,PI2 -D9,PA15 -D10,PI0 -D11,PB15 -D12,PB14 -D13,PI1 -D14,PB9 -D15,PB8 -LED,PI1 -SW,PI11 -TP1,PH2 -TP2,PI8 -TP3,PH15 -AUDIO_INT,PD6 -AUDIO_SDA,PH8 -AUDIO_SCL,PH7 -EXT_SDA,PB9 -EXT_SCL,PB8 -EXT_RST,PG3 -SD_D0,PC8 -SD_D1,PC9 -SD_D2,PC10 -SD_D3,PC11 -SD_CK,PC12 -SD_CMD,PD2 -SD_SW,PC13 -LCD_BL_CTRL,PK3 -LCD_INT,PI13 -LCD_SDA,PH8 -LCD_SCL,PH7 -OTG_FS_POWER,PD5 -OTG_FS_OVER_CURRENT,PD4 -OTG_HS_OVER_CURRENT,PE3 -USB_VBUS,PJ12 -USB_ID,PA10 -USB_DM,PA11 -USB_DP,PA12 -VCP_TX,PA9 -VCP_RX,PB7 diff --git a/stmhal/boards/STM32F7DISC/stm32f7xx_hal_conf.h b/stmhal/boards/STM32F7DISC/stm32f7xx_hal_conf.h deleted file mode 100644 index 3fbfb4310..000000000 --- a/stmhal/boards/STM32F7DISC/stm32f7xx_hal_conf.h +++ /dev/null @@ -1,429 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f7xx_hal_conf.h - * @author MCD Application Team - * @version V1.0.1 - * @date 25-June-2015 - * @brief HAL configuration file. - ****************************************************************************** - * @attention - * - * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F7xx_HAL_CONF_H -#define __STM32F7xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -#define USE_USB_FS - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -#define HAL_ADC_MODULE_ENABLED -#define HAL_CAN_MODULE_ENABLED -/* #define HAL_CEC_MODULE_ENABLED */ -/* #define HAL_CRC_MODULE_ENABLED */ -/* #define HAL_CRYP_MODULE_ENABLED */ -/* #define HAL_DAC_MODULE_ENABLED */ -/* #define HAL_DCMI_MODULE_ENABLED */ -#define HAL_DMA_MODULE_ENABLED -/* #define HAL_DMA2D_MODULE_ENABLED */ -/* #define HAL_ETH_MODULE_ENABLED */ -#define HAL_FLASH_MODULE_ENABLED -/* #define HAL_NAND_MODULE_ENABLED */ -/* #define HAL_NOR_MODULE_ENABLED */ -/* #define HAL_SRAM_MODULE_ENABLED */ -/* #define HAL_SDRAM_MODULE_ENABLED */ -/* #define HAL_HASH_MODULE_ENABLED */ -#define HAL_GPIO_MODULE_ENABLED -#define HAL_I2C_MODULE_ENABLED -#define HAL_I2S_MODULE_ENABLED -/* #define HAL_IWDG_MODULE_ENABLED */ -/* #define HAL_LPTIM_MODULE_ENABLED */ -/* #define HAL_LTDC_MODULE_ENABLED */ -#define HAL_PWR_MODULE_ENABLED -/* #define HAL_QSPI_MODULE_ENABLED */ -#define HAL_RCC_MODULE_ENABLED -#define HAL_RNG_MODULE_ENABLED -#define HAL_RTC_MODULE_ENABLED -/* #define HAL_SAI_MODULE_ENABLED */ -#define HAL_SD_MODULE_ENABLED -/* #define HAL_SPDIFRX_MODULE_ENABLED */ -#define HAL_SPI_MODULE_ENABLED -#define HAL_TIM_MODULE_ENABLED -#define HAL_UART_MODULE_ENABLED -/* #define HAL_USART_MODULE_ENABLED */ -/* #define HAL_IRDA_MODULE_ENABLED */ -/* #define HAL_SMARTCARD_MODULE_ENABLED */ -/* #define HAL_WWDG_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -#define HAL_PCD_MODULE_ENABLED -/* #define HAL_HCD_MODULE_ENABLED */ - - -/* ########################## Timeout Configuration ######################### */ -/** - * @brief This is the HAL configuration section - */ -#define HAL_ACCURATE_TIMEOUT_ENABLED 0 -#define HAL_TIMEOUT_VALUE 0x1FFFFFF - -/* ########################## HSE/HSI Values adaptation ##################### */ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE ((uint32_t)32000) -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature. */ -/** - * @brief External Low Speed oscillator (LSE) value. - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ -#endif /* LSE_VALUE */ - -#if !defined (LSE_STARTUP_TIMEOUT) - #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ -#endif /* LSE_STARTUP_TIMEOUT */ - -/** - * @brief External clock source for I2S peripheral - * This value is used by the I2S HAL module to compute the I2S clock source - * frequency, this source is inserted directly through I2S_CKIN pad. - */ -#if !defined (EXTERNAL_CLOCK_VALUE) - #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* EXTERNAL_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */ -#define USE_RTOS 0 -#define ART_ACCLERATOR_ENABLE 1 /* To enable instruction cache and prefetch */ - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1 */ - -/* ################## Ethernet peripheral configuration ##################### */ - -/* Section 1 : Ethernet peripheral configuration */ - -/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ -#define MAC_ADDR0 2 -#define MAC_ADDR1 1 -#define MAC_ADDR2 0 -#define MAC_ADDR3 0 -#define MAC_ADDR4 0 -#define MAC_ADDR5 0 - -/* Definition of the Ethernet driver buffers size and count */ -#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ -#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ -#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ -#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ - -/* Section 2: PHY configuration section */ -/* LAN8742A PHY Address*/ -#define LAN8742A_PHY_ADDRESS 0x00 -/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ -#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) -/* PHY Configuration delay */ -#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFF) - -#define PHY_READ_TO ((uint32_t)0x0000FFFF) -#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) - -/* Section 3: Common PHY Registers */ - -#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ -#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ - -#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ -#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ -#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ -#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ -#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ -#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ -#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ -#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ -#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ -#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ - -#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ -#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ -#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ - -/* Section 4: Extended PHY Registers */ - -#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ -#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ -#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ - -#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ -#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ -#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ - -#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ -#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ - -#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ -#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32f7xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32f7xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32f7xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32f7xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32f7xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32f7xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED - #include "stm32f7xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32f7xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED - #include "stm32f7xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DMA2D_MODULE_ENABLED - #include "stm32f7xx_hal_dma2d.h" -#endif /* HAL_DMA2D_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32f7xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_DCMI_MODULE_ENABLED - #include "stm32f7xx_hal_dcmi.h" -#endif /* HAL_DCMI_MODULE_ENABLED */ - -#ifdef HAL_ETH_MODULE_ENABLED - #include "stm32f7xx_hal_eth.h" -#endif /* HAL_ETH_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32f7xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED - #include "stm32f7xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED - #include "stm32f7xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED - #include "stm32f7xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_SDRAM_MODULE_ENABLED - #include "stm32f7xx_hal_sdram.h" -#endif /* HAL_SDRAM_MODULE_ENABLED */ - -#ifdef HAL_HASH_MODULE_ENABLED - #include "stm32f7xx_hal_hash.h" -#endif /* HAL_HASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32f7xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32f7xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32f7xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_LPTIM_MODULE_ENABLED - #include "stm32f7xx_hal_lptim.h" -#endif /* HAL_LPTIM_MODULE_ENABLED */ - -#ifdef HAL_LTDC_MODULE_ENABLED - #include "stm32f7xx_hal_ltdc.h" -#endif /* HAL_LTDC_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32f7xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_QSPI_MODULE_ENABLED - #include "stm32f7xx_hal_qspi.h" -#endif /* HAL_QSPI_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED - #include "stm32f7xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32f7xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SAI_MODULE_ENABLED - #include "stm32f7xx_hal_sai.h" -#endif /* HAL_SAI_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED - #include "stm32f7xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SPDIFRX_MODULE_ENABLED - #include "stm32f7xx_hal_spdifrx.h" -#endif /* HAL_SPDIFRX_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32f7xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32f7xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32f7xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32f7xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32f7xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32f7xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32f7xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32f7xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED - #include "stm32f7xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t* file, uint32_t line); -#else - #define assert_param(expr) ((void)0) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F7xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |