diff options
Diffstat (limited to 'stmhal/boards/STM32F769DISC/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/STM32F769DISC/mpconfigboard.h | 78 |
1 files changed, 0 insertions, 78 deletions
diff --git a/stmhal/boards/STM32F769DISC/mpconfigboard.h b/stmhal/boards/STM32F769DISC/mpconfigboard.h deleted file mode 100644 index 50b9c1618..000000000 --- a/stmhal/boards/STM32F769DISC/mpconfigboard.h +++ /dev/null @@ -1,78 +0,0 @@ -// This board is confirmed to operate using stlink and openocd. -// REPL is on UART(1) and is available through the stlink USB-UART device. -// To use openocd run "OPENOCD_CONFIG=boards/openocd_stm32f7.cfg" in -// the make command. -#define MICROPY_HW_BOARD_NAME "F769DISC" -#define MICROPY_HW_MCU_NAME "STM32F769" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (0) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (1) - -// HSE is 25MHz -// VCOClock = HSE * PLLN / PLLM = 25 MHz * 432 / 25 = 432 MHz -// SYSCLK = VCOClock / PLLP = 432 MHz / 2 = 216 MHz -// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 432 MHz / 9 = 48 MHz -#define MICROPY_HW_CLK_PLLM (25) -#define MICROPY_HW_CLK_PLLN (432) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (9) - -#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_7 // 210-216 MHz needs 7 wait states - -// UART config -#define MICROPY_HW_UART1_TX (pin_A9) -#define MICROPY_HW_UART1_RX (pin_A10) -#define MICROPY_HW_UART5_TX (pin_C12) -#define MICROPY_HW_UART5_RX (pin_D2) -#define MICROPY_HW_UART_REPL PYB_UART_1 -#define MICROPY_HW_UART_REPL_BAUD 115200 - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B8) -#define MICROPY_HW_I2C1_SDA (pin_B9) -#define MICROPY_HW_I2C3_SCL (pin_H7) -#define MICROPY_HW_I2C3_SDA (pin_H8) - -// SPI -#define MICROPY_HW_SPI2_NSS (pin_A11) -#define MICROPY_HW_SPI2_SCK (pin_A12) -#define MICROPY_HW_SPI2_MISO (pin_B14) -#define MICROPY_HW_SPI2_MOSI (pin_B15) - -// USRSW is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_A0) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_J13) // red -#define MICROPY_HW_LED2 (pin_J5) // green -#define MICROPY_HW_LED3 (pin_A12) // green -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// SD card detect switch -#define MICROPY_HW_SDMMC2_CK (pin_D6) -#define MICROPY_HW_SDMMC2_CMD (pin_D7) -#define MICROPY_HW_SDMMC2_D0 (pin_G9) -#define MICROPY_HW_SDMMC2_D1 (pin_G10) -#define MICROPY_HW_SDMMC2_D2 (pin_B3) -#define MICROPY_HW_SDMMC2_D3 (pin_B4) -#define MICROPY_HW_SDCARD_DETECT_PIN (pin_I15) -#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) -#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) - -// USB config (CN13 - USB OTG FS) -/*#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_J12)*/ -#define MICROPY_HW_USB_OTG_ID_PIN (pin_J12) |