diff options
Diffstat (limited to 'stmhal/boards/STM32F429DISC/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/STM32F429DISC/mpconfigboard.h | 73 |
1 files changed, 0 insertions, 73 deletions
diff --git a/stmhal/boards/STM32F429DISC/mpconfigboard.h b/stmhal/boards/STM32F429DISC/mpconfigboard.h deleted file mode 100644 index fc0702025..000000000 --- a/stmhal/boards/STM32F429DISC/mpconfigboard.h +++ /dev/null @@ -1,73 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "F429I-DISCO" -#define MICROPY_HW_MCU_NAME "STM32F429" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (0) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (0) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (1) - -// HSE is 8MHz -#define MICROPY_HW_CLK_PLLM (8) -#define MICROPY_HW_CLK_PLLN (336) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (7) - -// UART config -#define MICROPY_HW_UART1_TX (pin_A9) -#define MICROPY_HW_UART1_RX (pin_A10) -#define MICROPY_HW_UART2_TX (pin_D8) -#define MICROPY_HW_UART2_RX (pin_D9) - -// I2C busses -#define MICROPY_HW_I2C3_SCL (pin_A8) -#define MICROPY_HW_I2C3_SDA (pin_C9) - -// SPI busses -//#define MICROPY_HW_SPI1_NSS (pin_A4) -//#define MICROPY_HW_SPI1_SCK (pin_A5) -//#define MICROPY_HW_SPI1_MISO (pin_A6) -//#define MICROPY_HW_SPI1_MOSI (pin_A7) -#if defined(USE_USB_HS_IN_FS) -// The HS USB uses B14 & B15 for D- and D+ -#else -#define MICROPY_HW_SPI2_NSS (pin_B12) -#define MICROPY_HW_SPI2_SCK (pin_B13) -#define MICROPY_HW_SPI2_MISO (pin_B14) -#define MICROPY_HW_SPI2_MOSI (pin_B15) -#endif -//#define MICROPY_HW_SPI4_NSS (pin_E11) -//#define MICROPY_HW_SPI4_SCK (pin_E12) -//#define MICROPY_HW_SPI4_MISO (pin_E13) -//#define MICROPY_HW_SPI4_MOSI (pin_E14) -#define MICROPY_HW_SPI5_NSS (pin_F6) -#define MICROPY_HW_SPI5_SCK (pin_F7) -#define MICROPY_HW_SPI5_MISO (pin_F8) -#define MICROPY_HW_SPI5_MOSI (pin_F9) -//#define MICROPY_HW_SPI6_NSS (pin_G8) -//#define MICROPY_HW_SPI6_SCK (pin_G13) -//#define MICROPY_HW_SPI6_MISO (pin_G12) -//#define MICROPY_HW_SPI6_MOSI (pin_G14) - -// USRSW is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_A0) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_G14) // red -#define MICROPY_HW_LED2 (pin_G13) // green -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// USB config -#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_B13) -#define MICROPY_HW_USB_OTG_ID_PIN (pin_B12) |