diff options
Diffstat (limited to 'stmhal/boards/PYBV3/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/PYBV3/mpconfigboard.h | 88 |
1 files changed, 0 insertions, 88 deletions
diff --git a/stmhal/boards/PYBV3/mpconfigboard.h b/stmhal/boards/PYBV3/mpconfigboard.h deleted file mode 100644 index 1f49af4da..000000000 --- a/stmhal/boards/PYBV3/mpconfigboard.h +++ /dev/null @@ -1,88 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "PYBv3" -#define MICROPY_HW_MCU_NAME "STM32F405RG" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (1) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (1) -#define MICROPY_HW_ENABLE_CAN (1) - -// HSE is 8MHz -#define MICROPY_HW_CLK_PLLM (8) -#define MICROPY_HW_CLK_PLLN (336) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (7) - -// The pyboard has a 32kHz crystal for the RTC -#define MICROPY_HW_RTC_USE_LSE (1) - -// UART config -#define MICROPY_HW_UART1_TX (pin_A9) -#define MICROPY_HW_UART1_RX (pin_A10) -#define MICROPY_HW_UART2_TX (pin_A2) -#define MICROPY_HW_UART2_RX (pin_A3) -#define MICROPY_HW_UART2_RTS (pin_A1) -#define MICROPY_HW_UART2_CTS (pin_A0) -#define MICROPY_HW_UART3_TX (pin_B10) -#define MICROPY_HW_UART3_RX (pin_B11) -#define MICROPY_HW_UART3_RTS (pin_B14) -#define MICROPY_HW_UART3_CTS (pin_B13) -#define MICROPY_HW_UART4_TX (pin_A0) -#define MICROPY_HW_UART4_RX (pin_A1) -#define MICROPY_HW_UART6_TX (pin_C6) -#define MICROPY_HW_UART6_RX (pin_C7) - -// X-skin: X9=PB6=SCL, X10=PB7=SDA -#define MICROPY_HW_I2C1_SCL (pin_B6) -#define MICROPY_HW_I2C1_SDA (pin_B7) - -// Y-skin: Y9=PB10=SCL, Y10=PB11=SDA -#define MICROPY_HW_I2C2_SCL (pin_B10) -#define MICROPY_HW_I2C2_SDA (pin_B11) - -// SPI busses -#define MICROPY_HW_SPI1_NAME "X" -#define MICROPY_HW_SPI1_NSS (pin_A4) // X5 -#define MICROPY_HW_SPI1_SCK (pin_A5) // X6 -#define MICROPY_HW_SPI1_MISO (pin_A6) // X7 -#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8 -#define MICROPY_HW_SPI2_NAME "Y" -#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5 -#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6 -#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7 -#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8 - -// USRSW has no pullup or pulldown, and pressing the switch makes the input go low -#define MICROPY_HW_USRSW_PIN (pin_A13) -#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define MICROPY_HW_USRSW_PRESSED (0) - -// LEDs -#define MICROPY_HW_LED_INVERTED (1) // LEDs are on when pin is driven low -#define MICROPY_HW_LED1 (pin_A8) // R1 - red -#define MICROPY_HW_LED2 (pin_A10) // R2 - red -#define MICROPY_HW_LED3 (pin_C4) // G1 - green -#define MICROPY_HW_LED4 (pin_C5) // G2 - green -#define MICROPY_HW_LED1_PWM { TIM1, 1, TIM_CHANNEL_1, GPIO_AF1_TIM1 } -#define MICROPY_HW_LED2_PWM { TIM1, 1, TIM_CHANNEL_3, GPIO_AF1_TIM1 } -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin)) - -// SD card detect switch -#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13) -#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLDOWN) -#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_SET) - -// USB VBUS detect pin -#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) - -// MMA accelerometer config -#define MICROPY_HW_MMA_AVDD_PIN (pin_B5) |