diff options
Diffstat (limited to 'stmhal/boards/PYBLITEV10/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/PYBLITEV10/mpconfigboard.h | 87 |
1 files changed, 0 insertions, 87 deletions
diff --git a/stmhal/boards/PYBLITEV10/mpconfigboard.h b/stmhal/boards/PYBLITEV10/mpconfigboard.h deleted file mode 100644 index 090ba4cf1..000000000 --- a/stmhal/boards/PYBLITEV10/mpconfigboard.h +++ /dev/null @@ -1,87 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "PYBLITEv1.0" -#define MICROPY_HW_MCU_NAME "STM32F411RE" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (1) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (1) -#define MICROPY_HW_ENABLE_RNG (0) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (0) - -// HSE is 12MHz -#define MICROPY_HW_CLK_PLLM (12) -#define MICROPY_HW_CLK_PLLN (192) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (4) -#define MICROPY_HW_CLK_LAST_FREQ (1) - -// Pyboard lite has an optional 32kHz crystal -#define MICROPY_HW_RTC_USE_LSE (1) -#define MICROPY_HW_RTC_USE_US (0) -#define MICROPY_HW_RTC_USE_CALOUT (1) - -// UART config -#define MICROPY_HW_UART1_NAME "XB" -#define MICROPY_HW_UART1_TX (pin_B6) -#define MICROPY_HW_UART1_RX (pin_B7) -#define MICROPY_HW_UART2_NAME "XA" -#define MICROPY_HW_UART2_TX (pin_A2) -#define MICROPY_HW_UART2_RX (pin_A3) -#define MICROPY_HW_UART2_RTS (pin_A1) -#define MICROPY_HW_UART2_CTS (pin_A0) -#define MICROPY_HW_UART6_NAME "YA" -#define MICROPY_HW_UART6_TX (pin_C6) -#define MICROPY_HW_UART6_RX (pin_C7) - -// I2C busses -#define MICROPY_HW_I2C1_NAME "X" -#define MICROPY_HW_I2C1_SCL (pin_B6) -#define MICROPY_HW_I2C1_SDA (pin_B7) -#define MICROPY_HW_I2C3_NAME "Y" -#define MICROPY_HW_I2C3_SCL (pin_A8) -#define MICROPY_HW_I2C3_SDA (pin_B8) - -// SPI busses -#define MICROPY_HW_SPI1_NAME "X" -#define MICROPY_HW_SPI1_NSS (pin_A4) // X5 -#define MICROPY_HW_SPI1_SCK (pin_A5) // X6 -#define MICROPY_HW_SPI1_MISO (pin_A6) // X7 -#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8 -#define MICROPY_HW_SPI2_NAME "Y" -#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5 -#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6 -#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7 -#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8 - -// USRSW has no pullup or pulldown, and pressing the switch makes the input go low -#define MICROPY_HW_USRSW_PIN (pin_B3) -#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define MICROPY_HW_USRSW_PRESSED (0) - -// The pyboard has 4 LEDs -#define MICROPY_HW_LED1 (pin_A13) // red -#define MICROPY_HW_LED2 (pin_A14) // green -#define MICROPY_HW_LED3 (pin_A15) // yellow -#define MICROPY_HW_LED4 (pin_B4) // blue -#define MICROPY_HW_LED3_PWM { TIM2, 2, TIM_CHANNEL_1, GPIO_AF1_TIM2 } -#define MICROPY_HW_LED4_PWM { TIM3, 3, TIM_CHANNEL_1, GPIO_AF2_TIM3 } -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// SD card detect switch -#define MICROPY_HW_SDCARD_DETECT_PIN (pin_B5) -#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) -#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) - -// USB config -#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) - -// MMA accelerometer config -#define MICROPY_HW_MMA_AVDD_PIN (pin_A10) |