diff options
Diffstat (limited to 'stmhal/boards/NUCLEO_F446RE/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/NUCLEO_F446RE/mpconfigboard.h | 64 |
1 files changed, 0 insertions, 64 deletions
diff --git a/stmhal/boards/NUCLEO_F446RE/mpconfigboard.h b/stmhal/boards/NUCLEO_F446RE/mpconfigboard.h deleted file mode 100644 index d801fa188..000000000 --- a/stmhal/boards/NUCLEO_F446RE/mpconfigboard.h +++ /dev/null @@ -1,64 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "NUCLEO-F446RE" -#define MICROPY_HW_MCU_NAME "STM32F446xx" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_ENABLE_RTC (1) - -// HSE is 8MHz, CPU freq set to 168MHz. Using PLLQ for USB this gives a nice -// 48 MHz clock for USB. To goto 180 MHz, I think that USB would need to be -// configured to use PLLSAI -#define MICROPY_HW_CLK_PLLM (8) -#define MICROPY_HW_CLK_PLLN (336) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (7) - -// UART config -#define MICROPY_HW_UART2_TX (pin_A2) -#define MICROPY_HW_UART2_RX (pin_A3) -#define MICROPY_HW_UART6_TX (pin_C6) -#define MICROPY_HW_UART6_RX (pin_C7) -// UART 2 connects to the STM32F103 (STLINK) on the Nucleo board -// and this is exposed as a USB Serial port. -#define MICROPY_HW_UART_REPL PYB_UART_2 -#define MICROPY_HW_UART_REPL_BAUD 115200 - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B6) // Arduino D10, pin 17 on CN10 -#define MICROPY_HW_I2C1_SDA (pin_B7) // pin 21 on CN7 -#define MICROPY_HW_I2C2_SCL (pin_B10) // Arduino D6, pin 25 on CN10 -#define MICROPY_HW_I2C2_SDA (pin_B3) // Arduino D3, pin 31 on CN10 -#define MICROPY_HW_I2C3_SCL (pin_A8) // Arduino D7, pin 23 on CN10 -#define MICROPY_HW_I2C3_SDA (pin_C9) // pin 1 on CN10 - -// SPI busses -#define MICROPY_HW_SPI1_NSS (pin_A15) // pin 17 on CN7 -#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10 -#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10 -#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10 - -#define MICROPY_HW_SPI2_NSS (pin_B12) // pin 16 on CN10 -#define MICROPY_HW_SPI2_SCK (pin_B13) // pin 30 on CN10 -#define MICROPY_HW_SPI2_MISO (pin_B14) // pin 28 on CN10 -#define MICROPY_HW_SPI2_MOSI (pin_B15) // pin 26 on CN10 - -#define MICROPY_HW_SPI3_NSS (pin_A4) // Arduino A2, pin 32 on CN7 -#define MICROPY_HW_SPI3_SCK (pin_B3) // Arduino D3, pin 31 on CN10 -#define MICROPY_HW_SPI3_MISO (pin_B4) // Arduino D5, pin 27 on CN10 -#define MICROPY_HW_SPI3_MOSI (pin_B5) // Arduino D4, pin 29 on CN10 - -#define MICROPY_HW_SPI4_NSS (pin_B12) // pin 16 on CN10 -#define MICROPY_HW_SPI4_SCK (pin_B13) // pin 30 on CN10 -#define MICROPY_HW_SPI4_MISO (pin_A1) // pin 30 on CN7 -#define MICROPY_HW_SPI4_MOSI (pin_A11) // pin 14 on CN10 - -// USRSW is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_C13) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define MICROPY_HW_USRSW_PRESSED (0) - -// LEDs -#define MICROPY_HW_LED1 (pin_A5) // Green LD2 LED on Nucleo -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) |