diff options
Diffstat (limited to 'stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h | 73 |
1 files changed, 0 insertions, 73 deletions
diff --git a/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h b/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h deleted file mode 100644 index 9586ae4e5..000000000 --- a/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h +++ /dev/null @@ -1,73 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "NetduinoPlus2" -#define MICROPY_HW_MCU_NAME "STM32F405RG" - -#define MICROPY_HW_HAS_SWITCH (1) - -#define MICROPY_HW_HAS_FLASH (1) -// On the netuino, the sdcard appears to be wired up as a 1-bit -// SPI, so the driver needs to be converted to support that before -// we can turn this on. -#define MICROPY_HW_HAS_SDCARD (0) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (0) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (0) - -void NETDUINO_PLUS_2_board_early_init(void); -#define MICROPY_BOARD_EARLY_INIT NETDUINO_PLUS_2_board_early_init - -// HSE is 25MHz -#define MICROPY_HW_CLK_PLLM (25) -#define MICROPY_HW_CLK_PLLN (336) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) -#define MICROPY_HW_CLK_PLLQ (7) - -// UART config -#define MICROPY_HW_UART1_TX (pin_A9) -#define MICROPY_HW_UART1_RX (pin_A10) -#define MICROPY_HW_UART2_TX (pin_A2) -#define MICROPY_HW_UART2_RX (pin_A3) -#define MICROPY_HW_UART2_RTS (pin_A1) -#define MICROPY_HW_UART2_CTS (pin_A0) -#define MICROPY_HW_UART3_TX (pin_D8) -#define MICROPY_HW_UART3_RX (pin_D9) -#define MICROPY_HW_UART3_RTS (pin_D12) -#define MICROPY_HW_UART3_CTS (pin_D11) -#define MICROPY_HW_UART4_TX (pin_A0) -#define MICROPY_HW_UART4_RX (pin_A1) -#define MICROPY_HW_UART5_TX (pin_C12) -#define MICROPY_HW_UART5_RX (pin_D2) -#define MICROPY_HW_UART6_TX (pin_C6) -#define MICROPY_HW_UART6_RX (pin_C7) - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B6) -#define MICROPY_HW_I2C1_SDA (pin_B7) - -// SPI busses -#define MICROPY_HW_SPI2_NSS (pin_B12) -#define MICROPY_HW_SPI2_SCK (pin_B13) -#define MICROPY_HW_SPI2_MISO (pin_B14) -#define MICROPY_HW_SPI2_MOSI (pin_B15) - -// USRSW is pulled low. Pressing the button makes the input go high. -#define MICROPY_HW_USRSW_PIN (pin_B11) -#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// LEDs -#define MICROPY_HW_LED1 (pin_A10) // Blue LED -#define MICROPY_HW_LED2 (pin_C13) // White LED (aka Power) -#define MICROPY_HW_LED3 (pin_A10) // Same as Led(1) -#define MICROPY_HW_LED4 (pin_C13) // Same as Led(2) -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) - -// USB VBUS detect pin -#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) |