diff options
Diffstat (limited to 'stmhal/boards/ESPRUINO_PICO/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/ESPRUINO_PICO/mpconfigboard.h | 72 |
1 files changed, 0 insertions, 72 deletions
diff --git a/stmhal/boards/ESPRUINO_PICO/mpconfigboard.h b/stmhal/boards/ESPRUINO_PICO/mpconfigboard.h deleted file mode 100644 index d065180d8..000000000 --- a/stmhal/boards/ESPRUINO_PICO/mpconfigboard.h +++ /dev/null @@ -1,72 +0,0 @@ -#define MICROPY_HW_BOARD_NAME "Espruino Pico" -#define MICROPY_HW_MCU_NAME "STM32F401CD" - -#define MICROPY_EMIT_THUMB (0) -#define MICROPY_EMIT_INLINE_THUMB (0) -#define MICROPY_PY_BUILTINS_COMPLEX (0) -#define MICROPY_PY_USOCKET (0) -#define MICROPY_PY_NETWORK (0) - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_FLASH (1) -#define MICROPY_HW_HAS_SDCARD (0) -#define MICROPY_HW_HAS_MMA7660 (0) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_ENABLE_RNG (0) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (0) -#define MICROPY_HW_ENABLE_CAN (0) - -// Pico has an 8 MHz HSE and the F401 does 84 MHz max -#define MICROPY_HW_CLK_PLLM (5) -#define MICROPY_HW_CLK_PLLN (210) -#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4) -#define MICROPY_HW_CLK_PLLQ (7) - -// does not have a 32kHz crystal -#define MICROPY_HW_RTC_USE_LSE (0) - -// UART config -#define MICROPY_HW_UART1_TX (pin_B6) -#define MICROPY_HW_UART1_RX (pin_B7) -#define MICROPY_HW_UART2_TX (pin_A2) -#define MICROPY_HW_UART2_RX (pin_A3) -#define MICROPY_HW_UART2_RTS (pin_A1) -#define MICROPY_HW_UART2_CTS (pin_A0) -#define MICROPY_HW_UART6_TX (pin_A11) -#define MICROPY_HW_UART6_RX (pin_A12) - -// I2C busses -#define MICROPY_HW_I2C1_SCL (pin_B6) -#define MICROPY_HW_I2C1_SDA (pin_B7) -#define MICROPY_HW_I2C2_SCL (pin_B10) -#define MICROPY_HW_I2C2_SDA (pin_B3) -#define MICROPY_HW_I2C3_SCL (pin_A8) -#define MICROPY_HW_I2C3_SDA (pin_B4) - -// SPI busses -#define MICROPY_HW_SPI1_NSS (pin_A4) -#define MICROPY_HW_SPI1_SCK (pin_A5) -#define MICROPY_HW_SPI1_MISO (pin_A6) -#define MICROPY_HW_SPI1_MOSI (pin_A7) -#define MICROPY_HW_SPI2_NSS (pin_B12) -#define MICROPY_HW_SPI2_SCK (pin_B13) -#define MICROPY_HW_SPI2_MISO (pin_B14) -#define MICROPY_HW_SPI2_MOSI (pin_B15) - -// BTN1 has no pullup or pulldown; it is active high and broken out on a header -#define MICROPY_HW_USRSW_PIN (pin_C13) -#define MICROPY_HW_USRSW_PULL (GPIO_PULLDOWN) -#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define MICROPY_HW_USRSW_PRESSED (1) - -// Pico has 2 LEDs -#define MICROPY_HW_LED1 (pin_B2) // red -#define MICROPY_HW_LED2 (pin_B12) // green -#define MICROPY_HW_LED3 (pin_B12) // green -#define MICROPY_HW_LED4 (pin_B12) // green -#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) -#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) |