1 files changed, 83 insertions, 0 deletions
diff --git a/ports/stm32/boards/NUCLEO_F429ZI/mpconfigboard.h b/ports/stm32/boards/NUCLEO_F429ZI/mpconfigboard.h
new file mode 100644
index 000000000..42cc9d68c
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_F429ZI/mpconfigboard.h
@@ -0,0 +1,83 @@
+#define MICROPY_HW_BOARD_NAME       "NUCLEO-F429ZI"
+#define MICROPY_HW_MCU_NAME         "STM32F429"
+
+#define MICROPY_HW_HAS_SWITCH       (1)
+#define MICROPY_HW_HAS_FLASH        (1)
+#define MICROPY_HW_HAS_SDCARD       (0)
+#define MICROPY_HW_HAS_MMA7660      (0)
+#define MICROPY_HW_HAS_LIS3DSH      (0)
+#define MICROPY_HW_HAS_LCD          (0)
+#define MICROPY_HW_ENABLE_RNG       (1)
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_TIMER     (1)
+#define MICROPY_HW_ENABLE_SERVO     (0)
+#define MICROPY_HW_ENABLE_DAC       (0)
+#define MICROPY_HW_ENABLE_CAN       (1)
+
+// HSE is 8MHz
+#define MICROPY_HW_CLK_PLLM (8)
+#define MICROPY_HW_CLK_PLLN (180)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
+#define MICROPY_HW_CLK_PLLQ (4)
+
+// From the reference manual, for 2.7V to 3.6V
+// 151-180 MHz => 5 wait states
+// 181-210 MHz => 6 wait states
+// 211-216 MHz => 7 wait states
+#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_6
+
+// UART config
+#define MICROPY_HW_UART1_TX     (pin_A9)
+#define MICROPY_HW_UART1_RX     (pin_A10)
+
+#define MICROPY_HW_UART2_TX     (pin_D5)
+#define MICROPY_HW_UART2_RX     (pin_D6)
+
+#define MICROPY_HW_UART3_TX     (pin_D8)
+#define MICROPY_HW_UART3_RX     (pin_D9)
+
+#define MICROPY_HW_UART4_TX     (pin_A0)
+#define MICROPY_HW_UART4_RX     (pin_C11)
+
+#define MICROPY_HW_UART5_TX     (pin_C12)
+#define MICROPY_HW_UART5_RX     (pin_D2)
+
+#define MICROPY_HW_UART_REPL        PYB_UART_3
+#define MICROPY_HW_UART_REPL_BAUD   115200
+
+// I2C busses
+#define MICROPY_HW_I2C3_SCL (pin_A8)
+#define MICROPY_HW_I2C3_SDA (pin_C9)
+
+// SPI busses
+#define MICROPY_HW_SPI1_NSS     (pin_A4)
+#define MICROPY_HW_SPI1_SCK     (pin_B3)
+#define MICROPY_HW_SPI1_MISO    (pin_B4)
+#define MICROPY_HW_SPI1_MOSI    (pin_B5)
+
+#define MICROPY_HW_SPI4_NSS     (pin_E4)
+#define MICROPY_HW_SPI4_SCK     (pin_E2)
+#define MICROPY_HW_SPI4_MISO    (pin_E5)
+#define MICROPY_HW_SPI4_MOSI    (pin_E6)
+
+#define MICROPY_HW_SPI5_NSS     (pin_F6)
+#define MICROPY_HW_SPI5_SCK     (pin_F7)
+#define MICROPY_HW_SPI5_MISO    (pin_F8)
+#define MICROPY_HW_SPI5_MOSI    (pin_F9)
+
+// USRSW is pulled low. Pressing the button makes the input go high.
+#define MICROPY_HW_USRSW_PIN        (pin_C13)
+#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
+#define MICROPY_HW_USRSW_PRESSED    (1)
+
+// LEDs
+#define MICROPY_HW_LED1             (pin_B0) // green
+#define MICROPY_HW_LED2             (pin_B7) // blue
+#define MICROPY_HW_LED3             (pin_B14) // red
+#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
+#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
+
+// USB config (CN13 - USB OTG FS)
+#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
+#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)