diff options
Diffstat (limited to 'ports/stm32/boards/NUCLEO_F412ZG/mpconfigboard.h')
| -rw-r--r-- | ports/stm32/boards/NUCLEO_F412ZG/mpconfigboard.h | 82 |
1 files changed, 82 insertions, 0 deletions
diff --git a/ports/stm32/boards/NUCLEO_F412ZG/mpconfigboard.h b/ports/stm32/boards/NUCLEO_F412ZG/mpconfigboard.h new file mode 100644 index 000000000..2a557f135 --- /dev/null +++ b/ports/stm32/boards/NUCLEO_F412ZG/mpconfigboard.h @@ -0,0 +1,82 @@ +#define MICROPY_HW_BOARD_NAME "NUCLEO-F412ZG" +#define MICROPY_HW_MCU_NAME "STM32F412Zx" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_USB (1) + +// HSE is 8MHz, CPU freq set to 96MHz +#define MICROPY_HW_CLK_PLLM (8) +#define MICROPY_HW_CLK_PLLN (192) +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) +#define MICROPY_HW_CLK_PLLQ (4) + +#define MICROPY_HW_UART1_TX (pin_B6) +#define MICROPY_HW_UART1_RX (pin_B3) +#define MICROPY_HW_UART2_TX (pin_D5) +#define MICROPY_HW_UART2_RX (pin_D6) +#define MICROPY_HW_UART3_TX (pin_D8) +#define MICROPY_HW_UART3_RX (pin_D9) +#define MICROPY_HW_UART6_TX (pin_G14) +#define MICROPY_HW_UART6_RX (pin_G9) +#define MICROPY_HW_UART_REPL PYB_UART_3 +#define MICROPY_HW_UART_REPL_BAUD 115200 + +// I2C buses +#define MICROPY_HW_I2C1_SCL (pin_B8) +#define MICROPY_HW_I2C1_SDA (pin_B9) +#define MICROPY_HW_I2C2_SCL (pin_F1) +#define MICROPY_HW_I2C2_SDA (pin_F0) +#define MICROPY_HW_I2C3_SCL (pin_A8) +#define MICROPY_HW_I2C3_SDA (pin_C9) + +// SPI buses +#define MICROPY_HW_SPI1_NSS (pin_A4) // shared with DAC +#define MICROPY_HW_SPI1_SCK (pin_A5) // shared with DAC +#define MICROPY_HW_SPI1_MISO (pin_A6) +#define MICROPY_HW_SPI1_MOSI (pin_A7) +#define MICROPY_HW_SPI2_NSS (pin_B12) +#define MICROPY_HW_SPI2_SCK (pin_C7) +#define MICROPY_HW_SPI2_MISO (pin_C2) +#define MICROPY_HW_SPI2_MOSI (pin_C3) +#define MICROPY_HW_SPI3_NSS (pin_A15) +#define MICROPY_HW_SPI3_SCK (pin_C10) +#define MICROPY_HW_SPI3_MISO (pin_C11) +#define MICROPY_HW_SPI3_MOSI (pin_B5) +#define MICROPY_HW_SPI4_NSS (pin_E4) +#define MICROPY_HW_SPI4_SCK (pin_B13) +#define MICROPY_HW_SPI4_MISO (pin_E5) +#define MICROPY_HW_SPI4_MOSI (pin_E6) +#define MICROPY_HW_SPI5_NSS (pin_E11) +#define MICROPY_HW_SPI5_SCK (pin_E12) +#define MICROPY_HW_SPI5_MISO (pin_E13) +#define MICROPY_HW_SPI5_MOSI (pin_E14) + +// CAN buses +#define MICROPY_HW_CAN1_TX (pin_G1) +#define MICROPY_HW_CAN1_RX (pin_G0) +#define MICROPY_HW_CAN2_TX (pin_G12) +#define MICROPY_HW_CAN2_RX (pin_G11) + +// USRSW is pulled low. Pressing the button makes the input go high. +#define MICROPY_HW_USRSW_PIN (pin_C13) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) + +// LEDs +#define MICROPY_HW_LED1 (pin_B0) // Green +#define MICROPY_HW_LED2 (pin_B7) // Blue +#define MICROPY_HW_LED3 (pin_B14) // Red +#define MICROPY_HW_LED1_PWM { TIM1, 1, TIM_CHANNEL_2, GPIO_AF1_TIM1 } +#define MICROPY_HW_LED2_PWM { TIM4, 4, TIM_CHANNEL_2, GPIO_AF2_TIM4 } +#define MICROPY_HW_LED3_PWM { TIM12, 12, TIM_CHANNEL_1, GPIO_AF9_TIM12 } +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) + +// USB config (CN13 - USB OTG FS) +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) |