diff options
Diffstat (limited to 'ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h')
| -rw-r--r-- | ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h | 60 |
1 files changed, 60 insertions, 0 deletions
diff --git a/ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h b/ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h new file mode 100644 index 000000000..da219abd3 --- /dev/null +++ b/ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h @@ -0,0 +1,60 @@ +/* This file is part of the MicroPython project, http://micropython.org/ + * MIT License; Copyright (c) 2019 Damien P. George + */ + +#define MICROPY_HW_BOARD_NAME "B-L072Z-LRWAN1" +#define MICROPY_HW_MCU_NAME "STM32L072CZ" + +#define MICROPY_EMIT_THUMB (0) +#define MICROPY_EMIT_INLINE_THUMB (0) +#define MICROPY_PY_BUILTINS_COMPLEX (0) +#define MICROPY_PY_MATH (0) +#define MICROPY_PY_FRAMEBUF (0) +#define MICROPY_PY_USOCKET (0) +#define MICROPY_PY_NETWORK (0) +#define MICROPY_PY_STM (0) +#define MICROPY_PY_PYB_LEGACY (0) +#define MICROPY_VFS_FAT (0) + +#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_ADC (0) +#define MICROPY_HW_HAS_SWITCH (1) + +// UART config +#define MICROPY_HW_UART1_TX (pin_A9) +#define MICROPY_HW_UART1_RX (pin_A10) +#define MICROPY_HW_UART2_TX (pin_A2) +#define MICROPY_HW_UART2_RX (pin_A3) + +// USART2 is connected to the ST-LINK USB VCP +#define MICROPY_HW_UART_REPL PYB_UART_2 +#define MICROPY_HW_UART_REPL_BAUD 115200 + +// I2C busses +#define MICROPY_HW_I2C1_SCL (pin_B8) +#define MICROPY_HW_I2C1_SDA (pin_B9) + +// SPI busses +#define MICROPY_HW_SPI1_NSS (pin_A15) +#define MICROPY_HW_SPI1_SCK (pin_A5) +#define MICROPY_HW_SPI1_MISO (pin_A6) +#define MICROPY_HW_SPI1_MOSI (pin_A7) +#define MICROPY_HW_SPI2_NSS (pin_B12) +#define MICROPY_HW_SPI2_SCK (pin_B13) +#define MICROPY_HW_SPI2_MISO (pin_B14) +#define MICROPY_HW_SPI2_MOSI (pin_B15) + +// USER B1 has a pull-up and is active low +#define MICROPY_HW_USRSW_PIN (pin_B2) +#define MICROPY_HW_USRSW_PULL (0) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// 4 user LEDs +#define MICROPY_HW_LED1 (pin_B5) // Green +#define MICROPY_HW_LED2 (pin_A5) // Green (next to power LED) +#define MICROPY_HW_LED3 (pin_B6) // Blue +#define MICROPY_HW_LED4 (pin_B7) // Red +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) |