ports: Make new ports/ sub-directory and move all ports there.

This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.

5 files changed, 0 insertions, 684 deletions

diff --git a/stmhal/boards/STM32F4DISC/mpconfigboard.h b/stmhal/boards/STM32F4DISC/mpconfigboard.h
deleted file mode 100644
index 105875515..000000000
--- a/stmhal/boards/STM32F4DISC/mpconfigboard.h
+++ /dev/null
@@ -1,86 +0,0 @@
-#define STM32F4DISC
-
-#define MICROPY_HW_BOARD_NAME       "F4DISC"
-#define MICROPY_HW_MCU_NAME         "STM32F407"
-
-#define MICROPY_HW_HAS_SWITCH       (1)
-#define MICROPY_HW_HAS_FLASH        (1)
-#define MICROPY_HW_HAS_SDCARD       (0)
-#define MICROPY_HW_HAS_MMA7660      (0)
-#define MICROPY_HW_HAS_LIS3DSH      (1)
-#define MICROPY_HW_HAS_LCD          (0)
-#define MICROPY_HW_ENABLE_RNG       (1)
-#define MICROPY_HW_ENABLE_RTC       (1)
-#define MICROPY_HW_ENABLE_TIMER     (1)
-#define MICROPY_HW_ENABLE_SERVO     (0)
-#define MICROPY_HW_ENABLE_DAC       (1)
-#define MICROPY_HW_ENABLE_CAN       (1)
-
-// HSE is 8MHz
-#define MICROPY_HW_CLK_PLLM (8)
-#define MICROPY_HW_CLK_PLLN (336)
-#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
-#define MICROPY_HW_CLK_PLLQ (7)
-
-// UART config
-#if 0
-// A9 is used for USB VBUS detect, and A10 is used for USB_FS_ID.
-// UART1 is also on PB6/7 but PB6 is tied to the Audio SCL line.
-// Without board modifications, this makes UART1 unusable on this board.
-#define MICROPY_HW_UART1_TX     (pin_A9)
-#define MICROPY_HW_UART1_RX     (pin_A10)
-#endif
-#define MICROPY_HW_UART2_TX     (pin_A2)
-#define MICROPY_HW_UART2_RX     (pin_A3)
-#define MICROPY_HW_UART2_RTS    (pin_A1)
-#define MICROPY_HW_UART2_CTS    (pin_A0)
-#define MICROPY_HW_UART3_TX     (pin_D8)
-#define MICROPY_HW_UART3_RX     (pin_D9)
-#define MICROPY_HW_UART3_RTS    (pin_D12)
-#define MICROPY_HW_UART3_CTS    (pin_D11)
-#if MICROPY_HW_HAS_SWITCH == 0
-// NOTE: A0 also connects to the user switch. To use UART4 you should 
-//       set MICROPY_HW_HAS_SWITCH to 0, and also remove SB20 (on the back
-//       of the board near the USER switch).
-#define MICROPY_HW_UART4_TX     (pin_A0)
-#define MICROPY_HW_UART4_RX     (pin_A1)
-#endif
-// NOTE: PC7 is connected to MCLK on the Audio chip. This is an input signal
-//       so I think as long as you're not using the audio chip then it should
-//       be fine to use as a UART pin.
-#define MICROPY_HW_UART6_TX     (pin_C6)
-#define MICROPY_HW_UART6_RX     (pin_C7)
-
-// I2C busses
-#define MICROPY_HW_I2C1_SCL (pin_B6)
-#define MICROPY_HW_I2C1_SDA (pin_B7)
-#define MICROPY_HW_I2C2_SCL (pin_B10)
-#define MICROPY_HW_I2C2_SDA (pin_B11)
-
-// SPI busses
-#define MICROPY_HW_SPI1_NSS  (pin_A4)
-#define MICROPY_HW_SPI1_SCK  (pin_A5)
-#define MICROPY_HW_SPI1_MISO (pin_A6)
-#define MICROPY_HW_SPI1_MOSI (pin_A7)
-#define MICROPY_HW_SPI2_NSS  (pin_B12)
-#define MICROPY_HW_SPI2_SCK  (pin_B13)
-#define MICROPY_HW_SPI2_MISO (pin_B14)
-#define MICROPY_HW_SPI2_MOSI (pin_B15)
-
-// USRSW is pulled low. Pressing the button makes the input go high.
-#define MICROPY_HW_USRSW_PIN        (pin_A0)
-#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
-#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
-#define MICROPY_HW_USRSW_PRESSED    (1)
-
-// LEDs
-#define MICROPY_HW_LED1             (pin_D14) // red
-#define MICROPY_HW_LED2             (pin_D12) // green
-#define MICROPY_HW_LED3             (pin_D13) // orange
-#define MICROPY_HW_LED4             (pin_D15) // blue
-#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
-#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
-
-// USB config
-#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
-#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)
diff --git a/stmhal/boards/STM32F4DISC/mpconfigboard.mk b/stmhal/boards/STM32F4DISC/mpconfigboard.mk
deleted file mode 100644
index ece09caa1..000000000
--- a/stmhal/boards/STM32F4DISC/mpconfigboard.mk
+++ /dev/null
@@ -1,4 +0,0 @@
-MCU_SERIES = f4
-CMSIS_MCU = STM32F407xx
-AF_FILE = boards/stm32f405_af.csv
-LD_FILE = boards/stm32f405.ld
diff --git a/stmhal/boards/STM32F4DISC/pins.csv b/stmhal/boards/STM32F4DISC/pins.csv
deleted file mode 100644
index 4049fef7d..000000000
--- a/stmhal/boards/STM32F4DISC/pins.csv
+++ /dev/null
@@ -1,85 +0,0 @@
-PC0,PC0
-PC1,PC1
-PC2,PC2
-PC3,PC3
-PA0,PA0
-PA1,PA1
-PA2,PA2
-PA3,PA3
-PA4,PA4
-PA5,PA5
-PA6,PA6
-PA7,PA7
-PC4,PC4
-PC5,PC5
-PB0,PB0
-PB1,PB1
-PB2,PB2
-PE7,PE7
-PE8,PE8
-PE9,PE9
-PE10,PE10
-PE11,PE11
-PE12,PE12
-PE13,PE13
-PE14,PE14
-PE15,PE15
-PB10,PB10
-PB11,PB11
-PB12,PB12
-PB13,PB13
-PB14,PB14
-PB15,PB15
-PD8,PD8
-PD9,PD9
-PD10,PD10
-PD11,PD11
-PD12,PD12
-PD13,PD13
-PD14,PD14
-PD15,PD15
-PC6,PC6
-PC7,PC7
-PC8,PC8
-PC9,PC9
-PA8,PA8
-PA9,PA9
-PA10,PA10
-PA13,PA13
-PA14,PA14
-PA15,PA15
-PC10,PC10
-PC11,PC11
-PC12,PC12
-PD0,PD0
-PD1,PD1
-PD2,PD2
-PD3,PD3
-PD4,PD4
-PD5,PD5
-PD6,PD6
-PD7,PD7
-PB4,PB4
-PB5,PB5
-PB6,PB6
-PB7,PB7
-PB8,PB8
-PB9,PB9
-PE0,PE0
-PE1,PE1
-PE2,PE2
-PE3,PE3
-PE4,PE4
-PE5,PE5
-PE6,PE6
-PC13,PC13
-PC14,PC14
-PC15,PC15
-PH0,PH0
-PH1,PH1
-LED_GREEN,PD12
-LED_ORANGE,PD13
-LED_RED,PD14
-LED_BLUE,PD15
-SW,PA0
-
diff --git a/stmhal/boards/STM32F4DISC/staccel.py b/stmhal/boards/STM32F4DISC/staccel.py
deleted file mode 100644
index 2f2561d1c..000000000
--- a/stmhal/boards/STM32F4DISC/staccel.py
+++ /dev/null
@@ -1,98 +0,0 @@
-"""
-Driver for accelerometer on STM32F4 Discover board.
-
-Sets accelerometer range at +-2g.
-Returns list containing X,Y,Z axis acceleration values in 'g' units (9.8m/s^2).
-
-See:
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/Components/lis302dl/lis302dl.h
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/Components/lis302dl/lis302dl.c
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/STM32F4-Discovery/stm32f4_discovery.c
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/STM32F4-Discovery/stm32f4_discovery.h
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/STM32F4-Discovery/stm32f4_discovery_accelerometer.c
-    STM32Cube_FW_F4_V1.1.0/Drivers/BSP/STM32F4-Discovery/stm32f4_discovery_accelerometer.h
-    STM32Cube_FW_F4_V1.1.0/Projects/STM32F4-Discovery/Demonstrations/Src/main.c
-"""
-
-from micropython import const
-from pyb import Pin
-from pyb import SPI
-
-READWRITE_CMD = const(0x80) 
-MULTIPLEBYTE_CMD = const(0x40)
-WHO_AM_I_ADDR = const(0x0f)
-OUT_X_ADDR = const(0x29)
-OUT_Y_ADDR = const(0x2b)
-OUT_Z_ADDR = const(0x2d)
-OUT_T_ADDR = const(0x0c)
-
-LIS302DL_WHO_AM_I_VAL = const(0x3b)
-LIS302DL_CTRL_REG1_ADDR = const(0x20)
-# Configuration for 100Hz sampling rate, +-2g range
-LIS302DL_CONF = const(0b01000111)
-
-LIS3DSH_WHO_AM_I_VAL = const(0x3f)
-LIS3DSH_CTRL_REG4_ADDR = const(0x20)
-LIS3DSH_CTRL_REG5_ADDR = const(0x24)
-# Configuration for 100Hz sampling rate, +-2g range
-LIS3DSH_CTRL_REG4_CONF = const(0b01100111)
-LIS3DSH_CTRL_REG5_CONF = const(0b00000000)
-
-class STAccel:
-    def __init__(self):
-        self.cs_pin = Pin('PE3', Pin.OUT_PP, Pin.PULL_NONE)
-        self.cs_pin.high()
-        self.spi = SPI(1, SPI.MASTER, baudrate=328125, polarity=0, phase=1, bits=8)
-
-        self.who_am_i = self.read_id()
-
-        if self.who_am_i == LIS302DL_WHO_AM_I_VAL:
-            self.write_bytes(LIS302DL_CTRL_REG1_ADDR, bytearray([LIS302DL_CONF]))
-            self.sensitivity = 18
-        elif self.who_am_i == LIS3DSH_WHO_AM_I_VAL:
-            self.write_bytes(LIS3DSH_CTRL_REG4_ADDR, bytearray([LIS3DSH_CTRL_REG4_CONF]))
-            self.write_bytes(LIS3DSH_CTRL_REG5_ADDR, bytearray([LIS3DSH_CTRL_REG5_CONF]))
-            self.sensitivity = 0.06 * 256
-        else:
-            raise Exception('LIS302DL or LIS3DSH accelerometer not present')
-
-    def convert_raw_to_g(self, x):
-        if x & 0x80:
-            x = x - 256
-        return x * self.sensitivity / 1000
-
-    def read_bytes(self, addr, nbytes):
-        if nbytes > 1:
-            addr |= READWRITE_CMD | MULTIPLEBYTE_CMD
-        else:
-            addr |= READWRITE_CMD
-        self.cs_pin.low()
-        self.spi.send(addr)
-        #buf = self.spi.send_recv(bytearray(nbytes * [0])) # read data, MSB first
-        buf = self.spi.recv(nbytes)
-        self.cs_pin.high()
-        return buf
-
-    def write_bytes(self, addr, buf):
-        if len(buf) > 1:
-            addr |= MULTIPLEBYTE_CMD
-        self.cs_pin.low()
-        self.spi.send(addr)
-        for b in buf:
-            self.spi.send(b)
-        self.cs_pin.high()
-
-    def read_id(self):
-        return self.read_bytes(WHO_AM_I_ADDR, 1)[0]
-
-    def x(self):
-        return self.convert_raw_to_g(self.read_bytes(OUT_X_ADDR, 1)[0])
-
-    def y(self):
-        return self.convert_raw_to_g(self.read_bytes(OUT_Y_ADDR, 1)[0])
-
-    def z(self):
-        return self.convert_raw_to_g(self.read_bytes(OUT_Z_ADDR, 1)[0])
-
-    def xyz(self):
-        return (self.x(), self.y(), self.z())
diff --git a/stmhal/boards/STM32F4DISC/stm32f4xx_hal_conf.h b/stmhal/boards/STM32F4DISC/stm32f4xx_hal_conf.h
deleted file mode 100644
index 8941e8290..000000000
--- a/stmhal/boards/STM32F4DISC/stm32f4xx_hal_conf.h
+++ /dev/null
@@ -1,411 +0,0 @@
-/**

-  ******************************************************************************

-  * @file    stm32f4xx_hal_conf.h

-  * @author  MCD Application Team

-  * @version V1.1.0

-  * @date    19-June-2014

-  * @brief   HAL configuration file.

-  ******************************************************************************

-  * @attention

-  *

-  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>

-  *

-  * Redistribution and use in source and binary forms, with or without modification,

-  * are permitted provided that the following conditions are met:

-  *   1. Redistributions of source code must retain the above copyright notice,

-  *      this list of conditions and the following disclaimer.

-  *   2. Redistributions in binary form must reproduce the above copyright notice,

-  *      this list of conditions and the following disclaimer in the documentation

-  *      and/or other materials provided with the distribution.

-  *   3. Neither the name of STMicroelectronics nor the names of its contributors

-  *      may be used to endorse or promote products derived from this software

-  *      without specific prior written permission.

-  *

-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE

-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

-  *

-  ******************************************************************************

-  */ 

-

-/* Define to prevent recursive inclusion -------------------------------------*/

-#ifndef __STM32F4xx_HAL_CONF_H

-#define __STM32F4xx_HAL_CONF_H

-

-#ifdef __cplusplus

- extern "C" {

-#endif

-

-/* Exported types ------------------------------------------------------------*/

-/* Exported constants --------------------------------------------------------*/

-

-#define USE_USB_FS

-

-/* ########################## Module Selection ############################## */

-/**

-  * @brief This is the list of modules to be used in the HAL driver 

-  */

-#define HAL_MODULE_ENABLED

-#define HAL_ADC_MODULE_ENABLED

-#define HAL_CAN_MODULE_ENABLED

-/* #define HAL_CRC_MODULE_ENABLED */

-/* #define HAL_CRYP_MODULE_ENABLED */

-#define HAL_DAC_MODULE_ENABLED

-/* #define HAL_DCMI_MODULE_ENABLED */

-#define HAL_DMA_MODULE_ENABLED

-/* #define HAL_DMA2D_MODULE_ENABLED */

-/* #define HAL_ETH_MODULE_ENABLED */

-#define HAL_FLASH_MODULE_ENABLED

-/* #define HAL_NAND_MODULE_ENABLED */

-/* #define HAL_NOR_MODULE_ENABLED */

-/* #define HAL_PCCARD_MODULE_ENABLED */

-/* #define HAL_SRAM_MODULE_ENABLED */

-/* #define HAL_SDRAM_MODULE_ENABLED */

-/* #define HAL_HASH_MODULE_ENABLED */

-#define HAL_GPIO_MODULE_ENABLED

-#define HAL_I2C_MODULE_ENABLED

-/* #define HAL_I2S_MODULE_ENABLED */

-/* #define HAL_IWDG_MODULE_ENABLED */

-/* #define HAL_LTDC_MODULE_ENABLED */

-#define HAL_PWR_MODULE_ENABLED

-#define HAL_RCC_MODULE_ENABLED

-#define HAL_RNG_MODULE_ENABLED

-#define HAL_RTC_MODULE_ENABLED

-/* #define HAL_SAI_MODULE_ENABLED */

-#define HAL_SD_MODULE_ENABLED

-#define HAL_SPI_MODULE_ENABLED

-#define HAL_TIM_MODULE_ENABLED

-#define HAL_UART_MODULE_ENABLED

-/* #define HAL_USART_MODULE_ENABLED */

-/* #define HAL_IRDA_MODULE_ENABLED */

-/* #define HAL_SMARTCARD_MODULE_ENABLED */

-/* #define HAL_WWDG_MODULE_ENABLED */

-#define HAL_CORTEX_MODULE_ENABLED

-#define HAL_PCD_MODULE_ENABLED

-/* #define HAL_HCD_MODULE_ENABLED */

-

-

-/* ########################## HSE/HSI Values adaptation ##################### */

-/**

-  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.

-  *        This value is used by the RCC HAL module to compute the system frequency

-  *        (when HSE is used as system clock source, directly or through the PLL).  

-  */

-#if !defined  (HSE_VALUE) 

-  #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */

-#endif /* HSE_VALUE */

-

-#if !defined  (HSE_STARTUP_TIMEOUT)

-  #define HSE_STARTUP_TIMEOUT    ((uint32_t)100U)   /*!< Time out for HSE start up, in ms */

-#endif /* HSE_STARTUP_TIMEOUT */

-

-/**

-  * @brief Internal High Speed oscillator (HSI) value.

-  *        This value is used by the RCC HAL module to compute the system frequency

-  *        (when HSI is used as system clock source, directly or through the PLL). 

-  */

-#if !defined  (HSI_VALUE)

-  #define HSI_VALUE    ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/

-#endif /* HSI_VALUE */

-

-/**

-  * @brief Internal Low Speed oscillator (LSI) value.

-  */

-#if !defined  (LSI_VALUE) 

- #define LSI_VALUE  ((uint32_t)40000)    

-#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz

-                                             The real value may vary depending on the variations

-                                             in voltage and temperature.  */

-/**

-  * @brief External Low Speed oscillator (LSE) value.

-  */

-#if !defined  (LSE_VALUE)

- #define LSE_VALUE  ((uint32_t)32768)    /*!< Value of the External Low Speed oscillator in Hz */

-#endif /* LSE_VALUE */

-

-#if !defined  (LSE_STARTUP_TIMEOUT)

-  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000U)   /*!< Time out for LSE start up, in ms */

-#endif /* LSE_STARTUP_TIMEOUT */

-

-/**

-  * @brief External clock source for I2S peripheral

-  *        This value is used by the I2S HAL module to compute the I2S clock source 

-  *        frequency, this source is inserted directly through I2S_CKIN pad. 

-  */

-#if !defined  (EXTERNAL_CLOCK_VALUE)

-  #define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/

-#endif /* EXTERNAL_CLOCK_VALUE */

-

-/* Tip: To avoid modifying this file each time you need to use different HSE,

-   ===  you can define the HSE value in your toolchain compiler preprocessor. */

-

-/* ########################### System Configuration ######################### */

-/**

-  * @brief This is the HAL system configuration section

-  */     

-#define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */

-#define  TICK_INT_PRIORITY            ((uint32_t)0x00) /*!< tick interrupt priority */

-#define  USE_RTOS                     0

-#define  PREFETCH_ENABLE              1

-#define  INSTRUCTION_CACHE_ENABLE     1

-#define  DATA_CACHE_ENABLE            1

-

-/* ########################## Assert Selection ############################## */

-/**

-  * @brief Uncomment the line below to expanse the "assert_param" macro in the 

-  *        HAL drivers code

-  */

-/* #define USE_FULL_ASSERT    1 */

-

-/* ################## Ethernet peripheral configuration ##################### */

-

-/* Section 1 : Ethernet peripheral configuration */

-

-/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */

-#define MAC_ADDR0   2

-#define MAC_ADDR1   0

-#define MAC_ADDR2   0

-#define MAC_ADDR3   0

-#define MAC_ADDR4   0

-#define MAC_ADDR5   0

-

-/* Definition of the Ethernet driver buffers size and count */   

-#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */

-#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */

-#define ETH_RXBUFNB                    ((uint32_t)4)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */

-#define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */

-

-/* Section 2: PHY configuration section */

-

-/* DP83848 PHY Address*/ 

-#define DP83848_PHY_ADDRESS             0x01

-/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 

-#define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)

-/* PHY Configuration delay */

-#define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)

-

-#define PHY_READ_TO                     ((uint32_t)0x0000FFFF)

-#define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)

-

-/* Section 3: Common PHY Registers */

-

-#define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */

-#define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */

- 

-#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */

-#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */

-#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */

-#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */

-#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */

-#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */

-#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */

-#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */

-#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */

-#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */

-

-#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */

-#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */

-#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */

-  

-/* Section 4: Extended PHY Registers */

-

-#define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */

-#define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */

-#define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */

- 

-#define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */

-#define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */

-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */

-

-#define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */

-#define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */

-

-#define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */

-#define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */

-

-/* Includes ------------------------------------------------------------------*/

-/**

-  * @brief Include module's header file 

-  */

-

-#ifdef HAL_RCC_MODULE_ENABLED

-  #include "stm32f4xx_hal_rcc.h"

-#endif /* HAL_RCC_MODULE_ENABLED */

-

-#ifdef HAL_GPIO_MODULE_ENABLED

-  #include "stm32f4xx_hal_gpio.h"

-#endif /* HAL_GPIO_MODULE_ENABLED */

-

-#ifdef HAL_DMA_MODULE_ENABLED

-  #include "stm32f4xx_hal_dma.h"

-#endif /* HAL_DMA_MODULE_ENABLED */

-   

-#ifdef HAL_CORTEX_MODULE_ENABLED

-  #include "stm32f4xx_hal_cortex.h"

-#endif /* HAL_CORTEX_MODULE_ENABLED */

-

-#ifdef HAL_ADC_MODULE_ENABLED

-  #include "stm32f4xx_hal_adc.h"

-#endif /* HAL_ADC_MODULE_ENABLED */

-

-#ifdef HAL_CAN_MODULE_ENABLED

-  #include "stm32f4xx_hal_can.h"

-#endif /* HAL_CAN_MODULE_ENABLED */

-

-#ifdef HAL_CRC_MODULE_ENABLED

-  #include "stm32f4xx_hal_crc.h"

-#endif /* HAL_CRC_MODULE_ENABLED */

-

-#ifdef HAL_CRYP_MODULE_ENABLED

-  #include "stm32f4xx_hal_cryp.h" 

-#endif /* HAL_CRYP_MODULE_ENABLED */

-

-#ifdef HAL_DMA2D_MODULE_ENABLED

-  #include "stm32f4xx_hal_dma2d.h"

-#endif /* HAL_DMA2D_MODULE_ENABLED */

-

-#ifdef HAL_DAC_MODULE_ENABLED

-  #include "stm32f4xx_hal_dac.h"

-#endif /* HAL_DAC_MODULE_ENABLED */

-

-#ifdef HAL_DCMI_MODULE_ENABLED

-  #include "stm32f4xx_hal_dcmi.h"

-#endif /* HAL_DCMI_MODULE_ENABLED */

-

-#ifdef HAL_ETH_MODULE_ENABLED

-  #include "stm32f4xx_hal_eth.h"

-#endif /* HAL_ETH_MODULE_ENABLED */

-

-#ifdef HAL_FLASH_MODULE_ENABLED

-  #include "stm32f4xx_hal_flash.h"

-#endif /* HAL_FLASH_MODULE_ENABLED */

- 

-#ifdef HAL_SRAM_MODULE_ENABLED

-  #include "stm32f4xx_hal_sram.h"

-#endif /* HAL_SRAM_MODULE_ENABLED */

-

-#ifdef HAL_NOR_MODULE_ENABLED

-  #include "stm32f4xx_hal_nor.h"

-#endif /* HAL_NOR_MODULE_ENABLED */

-

-#ifdef HAL_NAND_MODULE_ENABLED

-  #include "stm32f4xx_hal_nand.h"

-#endif /* HAL_NAND_MODULE_ENABLED */

-

-#ifdef HAL_PCCARD_MODULE_ENABLED

-  #include "stm32f4xx_hal_pccard.h"

-#endif /* HAL_PCCARD_MODULE_ENABLED */ 

-  

-#ifdef HAL_SDRAM_MODULE_ENABLED

-  #include "stm32f4xx_hal_sdram.h"

-#endif /* HAL_SDRAM_MODULE_ENABLED */      

-

-#ifdef HAL_HASH_MODULE_ENABLED

- #include "stm32f4xx_hal_hash.h"

-#endif /* HAL_HASH_MODULE_ENABLED */

-

-#ifdef HAL_I2C_MODULE_ENABLED

- #include "stm32f4xx_hal_i2c.h"

-#endif /* HAL_I2C_MODULE_ENABLED */

-

-#ifdef HAL_I2S_MODULE_ENABLED

- #include "stm32f4xx_hal_i2s.h"

-#endif /* HAL_I2S_MODULE_ENABLED */

-

-#ifdef HAL_IWDG_MODULE_ENABLED

- #include "stm32f4xx_hal_iwdg.h"

-#endif /* HAL_IWDG_MODULE_ENABLED */

-

-#ifdef HAL_LTDC_MODULE_ENABLED

- #include "stm32f4xx_hal_ltdc.h"

-#endif /* HAL_LTDC_MODULE_ENABLED */

-

-#ifdef HAL_PWR_MODULE_ENABLED

- #include "stm32f4xx_hal_pwr.h"

-#endif /* HAL_PWR_MODULE_ENABLED */

-

-#ifdef HAL_RNG_MODULE_ENABLED

- #include "stm32f4xx_hal_rng.h"

-#endif /* HAL_RNG_MODULE_ENABLED */

-

-#ifdef HAL_RTC_MODULE_ENABLED

- #include "stm32f4xx_hal_rtc.h"

-#endif /* HAL_RTC_MODULE_ENABLED */

-

-#ifdef HAL_SAI_MODULE_ENABLED

- #include "stm32f4xx_hal_sai.h"

-#endif /* HAL_SAI_MODULE_ENABLED */

-

-#ifdef HAL_SD_MODULE_ENABLED

- #include "stm32f4xx_hal_sd.h"

-#endif /* HAL_SD_MODULE_ENABLED */

-

-#ifdef HAL_SPI_MODULE_ENABLED

- #include "stm32f4xx_hal_spi.h"

-#endif /* HAL_SPI_MODULE_ENABLED */

-

-#ifdef HAL_TIM_MODULE_ENABLED

- #include "stm32f4xx_hal_tim.h"

-#endif /* HAL_TIM_MODULE_ENABLED */

-

-#ifdef HAL_UART_MODULE_ENABLED

- #include "stm32f4xx_hal_uart.h"

-#endif /* HAL_UART_MODULE_ENABLED */

-

-#ifdef HAL_USART_MODULE_ENABLED

- #include "stm32f4xx_hal_usart.h"

-#endif /* HAL_USART_MODULE_ENABLED */

-

-#ifdef HAL_IRDA_MODULE_ENABLED

- #include "stm32f4xx_hal_irda.h"

-#endif /* HAL_IRDA_MODULE_ENABLED */

-

-#ifdef HAL_SMARTCARD_MODULE_ENABLED

- #include "stm32f4xx_hal_smartcard.h"

-#endif /* HAL_SMARTCARD_MODULE_ENABLED */

-

-#ifdef HAL_WWDG_MODULE_ENABLED

- #include "stm32f4xx_hal_wwdg.h"

-#endif /* HAL_WWDG_MODULE_ENABLED */

-

-#ifdef HAL_PCD_MODULE_ENABLED

- #include "stm32f4xx_hal_pcd.h"

-#endif /* HAL_PCD_MODULE_ENABLED */

-

-#ifdef HAL_HCD_MODULE_ENABLED

- #include "stm32f4xx_hal_hcd.h"

-#endif /* HAL_HCD_MODULE_ENABLED */

-   

-/* Exported macro ------------------------------------------------------------*/

-#ifdef  USE_FULL_ASSERT

-/**

-  * @brief  The assert_param macro is used for function's parameters check.

-  * @param  expr: If expr is false, it calls assert_failed function

-  *         which reports the name of the source file and the source

-  *         line number of the call that failed. 

-  *         If expr is true, it returns no value.

-  * @retval None

-  */

-  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))

-/* Exported functions ------------------------------------------------------- */

-  void assert_failed(uint8_t* file, uint32_t line);

-#else

-  #define assert_param(expr) ((void)0)

-#endif /* USE_FULL_ASSERT */

-

-

-#ifdef __cplusplus

-}

-#endif

-

-#endif /* __STM32F4xx_HAL_CONF_H */

- 

-

-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/