From 7ca1bd314bd5e3146f8c868f91af54d17dd04d45 Mon Sep 17 00:00:00 2001
From: Daniel Campora
Date: Wed, 27 May 2015 13:59:59 +0200
Subject: docs: Generate a separate docs build for each port.

Using Damien's approach where conf.py and topindex.html are
shared by all ports.
---
 docs/tutorial/reset.rst | 60 -------------------------------------------------
 1 file changed, 60 deletions(-)
 delete mode 100644 docs/tutorial/reset.rst

(limited to 'docs/tutorial/reset.rst')

diff --git a/docs/tutorial/reset.rst b/docs/tutorial/reset.rst
deleted file mode 100644
index 0cd5ac21c..000000000
--- a/docs/tutorial/reset.rst
+++ /dev/null
@@ -1,60 +0,0 @@
-Safe mode and factory reset
-===========================
-
-If something goes wrong with your pyboard, don't panic!  It is almost
-impossible for you to break the pyboard by programming the wrong thing.
-
-The first thing to try is to enter safe mode: this temporarily skips
-execution of ``boot.py`` and ``main.py`` and gives default USB settings.
-
-If you have problems with the filesystem you can do a factory reset,
-which restores the filesystem to its original state.
-
-Safe mode
----------
-
-To enter safe mode, do the following steps:
-
-1. Connect the pyboard to USB so it powers up.
-2. Hold down the USR switch.
-3. While still holding down USR, press and release the RST switch.
-4. The LEDs will then cycle green to orange to green+orange and back again.
-5. Keep holding down USR until *only the orange LED is lit*, and then let
-   go of the USR switch.
-6. The orange LED should flash quickly 4 times, and then turn off.  
-7. You are now in safe mode.
-
-In safe mode, the ``boot.py`` and ``main.py`` files are not executed, and so
-the pyboard boots up with default settings.  This means you now have access
-to the filesystem (the USB drive should appear), and you can edit ``boot.py``
-and ``main.py`` to fix any problems.
-
-Entering safe mode is temporary, and does not make any changes to the
-files on the pyboard.
-
-Factory reset the filesystem
-----------------------------
-
-If you pyboard's filesystem gets corrupted (for example, you forgot to
-eject/unmount it), or you have some code in ``boot.py`` or ``main.py`` which
-you can't escape from, then you can reset the filesystem.
-
-Resetting the filesystem deletes all files on the internal pyboard storage
-(not the SD card), and restores the files ``boot.py``, ``main.py``, ``README.txt``
-and ``pybcdc.inf`` back to their original state.
-
-To do a factory reset of the filesystem you follow a similar procedure as
-you did to enter safe mode, but release USR on green+orange:
-
-1. Connect the pyboard to USB so it powers up.
-2. Hold down the USR switch.
-3. While still holding down USR, press and release the RST switch.
-4. The LEDs will then cycle green to orange to green+orange and back again.
-5. Keep holding down USR until *both the green and orange LEDs are lit*, and
-   then let go of the USR switch.
-6. The green and orange LEDs should flash quickly 4 times.
-7. The red LED will turn on (so red, green and orange are now on).
-8. The pyboard is now resetting the filesystem (this takes a few seconds).
-9. The LEDs all turn off.
-10. You now have a reset filesystem, and are in safe mode.
-11. Press and release the RST switch to boot normally.
-- 
cgit v1.2.3